What causes a P0420 code?

What causes a P0420 code? (VIDEO)

If the front signals and the rear signals look identical, the catalyst is not doing its job. Sponsored by AP Emissions.

A recent EPA study showed that 7% of cars in the United States were operating below federally mandated emissions. 68% of those emissions failures were due to P0420 or 430 catalyst system inefficiency below threshold OBD 2 Code.

When a catalytic converter is working efficiently under closed lube operation, the front oxygen sensor will typically show an airfield mixture switching between rich and lean, rich and lean, rich and lean over a fast timeframe, as the car works to maintain a combustible airfield mixture, that’s optimal for the most power with the least emissions.

However, the signal from the rear 02 sensor that monitors that catalyst should not switch very much between the rich and lean. It should go basically a straight line when that converter is operating efficiently. The takeaway here is that if the front signals and the rear signals look identical, the catalyst is not doing its job.

When you start a car up, you can see the rear sensors showing fuel trim switching, between rich and lean. Older cars with front 02 sensors switch much more noticeably than newer cars with front air fuel ratio or lambda sensors.

Once that catalytic converter is warmed up, oxygen is alternately stored and released by the catalytic converter to maintain that catalytic converter reaction process. So until that catalytic converter is warmed up, both the front and the rear will switch between rich and lean over a fast timescale. The front will look like a mirror of the rear until the cat lights off and starts doing its thing. Then, after it’s all warmed up, it should be a mostly straight line out the rear. If the car’s all warmed up and you’re still seeing the rear sensor mirror that front, then your converter is not working properly. A 420 or 430 code, depending on which bank is triggered when the computer senses that the rear is switching more than it should. It knows this by comparing the signals of the rear catalyst monitor with the signals from the front air fuel ratio or oxygen sensor.

Sometimes manufacturers change the trigger point for 420 code by issuing an emissions related technical service bulletin and release an ECM flash update that loosens the trigger point for catalyst inefficiency code.

Catalyst system efficiency below threshold codes are usually caused by a failed catalytic converter. Sometimes it can be result of faulty sensors, circuit problems, an exhaust leak, or computer issue that needs updating.

A catalytic converter is a simple device. It’s got no moving parts and it rarely fails on its own. When a catalytic converter fails and you get a P0420 or 430 code, it’s the technician’s job to put on their detective hat and figure out what killed the cat.

In the next four videos, we’re going to discuss catalytic converter thermal damage and poisoning. Then we’ll review some diagnostic tips, grouped for simplicity under the traditional conceptual headings of air fuel and spark.

This video is sponsored by AP Emissions Technologies.

You May Also Like

At the Intersection of Tradition and Innovation with Grace Hovis

Grace Hovis’s journey in Hovis Auto & Truck Supply blends tradition with digital innovation in the automotive aftermarket industry.

Grace Hovis's journey in the family business, Hovis Auto and Truck Supply, highlights the balance between honoring tradition and seeking innovation. Founded in 1952, Hovis Auto and Truck Supply Inc. has evolved from a small operation into a major player in the automotive parts distribution space. This evolution was fueled by a willingness to adapt and innovate, a lesson Grace learned from an early age.

Why A 12-volt Battery is Still Essential in EVs

A device similar to an alternator, called a DC-DC converter, charges the 12-volt battery from the high-voltage battery pack.

Turbocharger Maintenance ft. Rein TechSelect Turbo Kits

Learn about common challenges with turbocharger maintenance and how Rein TechSelect Turbo Kitsmake the repair process easier for technicians.

The Standard® Advantage

Standard® knows that what comes out of a repair is directly dependent upon what goes into the box. This video is sponsored by Standard®.

TransFix: What Happens When a Transmission Has a Harsh Shift?

Learn about the additives and conditioners that can rejuvenate the seals and eliminate varnish in the passages of the valve body.

Other Posts

10 Commandments Of Catalytic Converter Replacement

Paperwork, laws and warranty issues can cause headaches.

Tesla Model 3 TPMS Service

Resetting and programming TPMS sensors for a Tesla is a lot like any other vehicle, and the challenge is still the same: keeping the light off.

Can You Jumpstart an EV?

First thing’s first: Find the LV battery, which could be anywhere in the vehicle.

Understanding What Antifreeze/Coolant Actually Does

Today, each manufacturer has its own formula for best results in their vehicles. This video is part of the Group Training Academy.