Tech Tip: Motor Mount Inspection Guidelines – UnderhoodService

Tech Tip: Motor Mount Inspection Guidelines

Most motor mounts are relatively simple in design and consist only of metal attachment plates and large rubber insulator blocks. But some vehicles have "hydraulic" or "hydro-mounts" with hollow chambers filled with glycol or hydraulic fluid.

Motor mounts are not a very glamorous product, but they do have an important function: They support the engine and transmission, and dampen noise and vibration. The mounts isolate the engine and transmission from the chassis so vibrations and noise are not transmitted to the rest of the vehicle. On some front-wheel drive cars, upper mounts (torque struts) also control the fore and aft movements of the engine during acceleration.

Most motor mounts are relatively simple in design and consist only of metal attachment plates and large rubber insulator blocks. But some vehicles have “hydraulic” or “hydro-mounts” with hollow chambers filled with glycol or hydraulic fluid. Hydro-mounts act like a jelly-filled donut to absorb vibrations that would otherwise be transmitted to the chassis. Hydro-mounts are often used with four-cylinder and V6 engines that don’t idle as smoothly as a V8, and in luxury vehicles where motorists expect less noise and vibration. Some hydro-mounts even have internal valving and/or a solenoid to change the dampening characteristics at different RPM to better tune out unwanted vibrations. These are called “switchable” hydraulic mounts or “electronic” mounts.

WHEN MOUNTS GO BAD
When a motor or transmission mount fails, one of several things can happen. If the rubber separates or delaminates from the steel, the mount can break. The design of the mount usually prevents the engine from falling out of the car, but it can’t keep the engine from twisting or rocking when the vehicle accelerates or is under load. This can produce thumping and rattling noises, as well as overstressing components such as radiator and heater hoses, wiring connectors and the exhaust system. In rear-wheel drive applications that have an engine-driven fan, a broken mount may allow the fan to hit the radiator or shroud. Drive belts or pulleys may also be forced to rub against other components if clearances are tight.

A broken or loose motor mount in a front-wheel drive application can be even more serious because it may allow engine movements that interfere with the throttle or shift linkage. Excessive fore and aft rocking of a transverse-mounted engine can also lead to exhaust leaks where the head pipe joins the manifold, or cause the head pipe itself to fail. If the broken mount is an end mount, it may also contribute to a torque steer condition and cause accelerated wear or separation of the inner CV joints on one or both halfshafts.

The motor mounts are seldom checked unless there is an obvious problem, and they may even be overlooked if the engine or transmission is being replaced. You should remind customers to check their motor mounts if the engines seem noisier than usual or they can feel engine vibrations inside their vehicles. The condition of the mounts should also be inspected when any major engine or transmission work is done, or when replacing a clutch, halfshafts or a driveshaft.

Mounts can be visually inspected for cracked, loose or broken brackets, loose or missing bolts, collapsed rubber or fluid leaks (hydro-mounts). A pry bar can be used to check for separated or broken mounts.

Another way to check mounts is to put the transmission into drive and lightly load the engine while keeping the other foot on the brake. Excessive engine movement may indicate loose or broken mounts that need to be replaced.

Replacement mounts may or may not have the same construction as the original. Fluid-filled hydro-mounts are expensive, so a more affordable alternative may be a solid replacement mount. But a solid mount obviously can’t provide the same level of dampening as the original hydro-mount. Consequently, the vehicle owner may not be happy with the way his car feels if a less-expensive solid mount is substituted for a fluid-filled mount.

You May Also Like

Lifter Deactivation

The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine.

The basic function of a valve lifter is pretty simple. It sits on the camshaft and transfers the motions of the cam lobe up through the pushrods and rockers to open and close the valves. The size and shape of the cam lobe under the lifter (multiplied by the ratio of the rocker arms) determine valve lift and duration. As such, the lifter just follows the motions of the cam. But, it does play a role in valvetrain lash (clearance) and noise.

Alternator Testing For No Charge Conditions

Many alternator problems turn out to be nothing more than a bad connection at the alternator or a bad wiring harness.

Understanding Coolants

All-season coolant used inorganic acid technology and worked great for almost 30 years.

Ignition System Do’s and Don’ts

Why do ignition systems give technicians problems when diagnosing ignition-related misfires? The answer is that some technicians use tests that might give inconclusive results or do damage to the coil or drivers inside a module.

Tools To Service Serpentine Belts

Servicing the serpentine belt on some vehicles is a tough task.

Other Posts

Detecting Misfire And Knock Conditions

Knock sensors are mounted on the block near the base of the cylinder head.

Battery Charging and Diagnostics

Here are six tips to use when diagnosing a vehicle with a dead battery. 

Why Do Timing Chains Stretch?

As the timing chain wears, it can change the timing of the camshaft and crankshaft.

Carbon Deposits and Direct Injection Engines

The primary cause of these problems is that fuel and added detergents are not hitting the back of the intake valves.