Carbon Deposits and Direct Injection Engines

Carbon Deposits and Direct Injection Engines

The primary cause of these problems is that fuel and added detergents are not hitting the back of the intake valves.

In the late ‘90s and early 2000s, TSBs related to carbon deposits on the valves were few and far between. There are three reasons why direct-injection engines are more prone to carbon deposits. One reason is unique to direct injection, and the remaining two are problems for port fuel-injection engines that are made worse by direct injection.

The primary cause of these problems is that fuel and added detergents are not hitting the back of the intake valves. By injecting the fuel directly into the cylinder instead of at the back of the valve, the gasoline and detergents can’t clean the valve and port.

Second, leaner mixtures and higher combustion pressures can make the problem worse over time. A direct fuel-injection motor produces more energy from a given amount of fuel and air than a port fuel-injection engine. Today’s engines operate on the edge between optimal efficiency and a misfire. There is not much room for errors like hot spots in the combustion chamber or a worn spark plug.

When a hot spot or sub-optimal flame front is created due to turbulent air, the amount of unburned fuel in the combustion chamber increases. When the valve opens during the intake stroke, it might come in contact with these byproducts and, unlike the exhaust valve, the gases passing by are not hot enough to burn it off.

Third, the intake valve goes into the combustion chamber, regardless if it is port fuel injected or direct injected. When it does, for that small period, it is exposed to combustion byproducts that can stick to the neck of the valve. If the last combustion cycle was less than optimal, the intake valve is exposed.

Some direct-injection vehicles with variable valve timing can expose the valve to combustion byproducts as the valves adjust, which creates a scavenging effect to either pull or leave behind a small amount of exhaust gas in the chamber to control NOX emissions. Also, some turbocharged direct-injection engines will leave the intake and exhaust valves open at the same time to keep the turbo spinning to reduce lag.

Why are some direct injection engines more prone to deposits?

If you look up direct-injection carbon deposit problems on the Internet, engines from BMW, Audi and VW always rank the highest. Engines from GM and Ford that have been on the road for at least four years hardly have a carbon deposit complaint. What’s the deal?

Some direct-injection engines can have unique timing cycles that can increase compression, temperatures and exposure of the valves to the combustion chamber.

The modern engine typically has variable valve timing and even cylinder deactivation. The engine management system can control when, how long and, in some cases, how deep the valve goes into the combustion chamber. If an intake valve is dropping into a combustion chamber with combustion byproducts or unburned fuel, the valve might be exposed to the precursors that cause carbon buildup.

Some carbon deposit problems are amplified due to the positive crankcase ventilation (PCV) systems. The crankcase vapors can leave an oily film on the intake valve that is then baked into carbon. Some blame the valve overlap during the intake stroke that eliminates the need for an EGR valve.

The Fix

There are several fixes available to solve carbon buildup problems.

The first is preventive maintenance. Scheduled oil changes can keep the camshaft actuators working in optimal condition to control the exposure of the intake valves. High-quality oils with lower volatility can reduce the volume of vapors in the crankcase.

In-tank fuel injector cleaners also can help injectors maintain the correct spray pattern. This can ensure that the droplets have the correct size and distribution during ignition. In addition, extra detergent can help to break down deposits. Induction cleaning products and systems can put solvents and detergents onto the back of the intake and in the combustion chambers. These two maintenance services can help reduce carbon buildup and possibly avoid having to take more drastic measures like blasting the valves with walnut shells.

One of the most effective methods for preventing a carbon buildup problem is updating the engine management software. New software can reduce carbon deposits by reducing the exposure of the valves to conditions that cause carbon buildup through the adjustment of valve and spark timing.

Don’t assume that you will find a TSB stating that a reflash of the ECM will correct a carbon buildup problem, because most of the regular updates may never say anything about a problem. You may even have to check the OEM’s website to see if the vehicle has the latest version of the software.

You May Also Like

It’s Got Spark!

Why can’t you trust some spark tests?

You have probably seen some reality TV shows where the “builder” will pull a spark plug wire to confirm they have spark. This is one of the most misleading tests for the ignition system. If the spark plug produces a spark, the spark is at 14.6 psi (normal air pressure at sea level), not 170 psi or more inside the cylinder during the top of the power stroke.

Diagnosing Intercooler Boost Trouble Code P0299

The criteria for setting the code is very basic.

Honda Electronic Throttle Body Service Tips

Using care and following OEM procedures will help you to avoid unnecessary parts replacement and comebacks.

Why Alternators Are Subject To Ripple Voltage

The alternator produces an AC current that must be converted into DC current by way of a rectifier.

Belts and Pulley Alignment

A misalignment of the plane of the belt can occur when a pulley is not parallel to the other pulleys on the belt drive system.

Other Posts

Diagnosing Misfires

What if there are no codes and a misfire is intermittent? This is where it gets complicated.

Lifter Deactivation

The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine.

Alternator Testing For No Charge Conditions

Many alternator problems turn out to be nothing more than a bad connection at the alternator or a bad wiring harness.

Understanding Coolants

All-season coolant used inorganic acid technology and worked great for almost 30 years.