Tech Tip: Diagnosing a Nissan Altima with the Check Engine Light On – UnderhoodService

Tech Tip: Diagnosing a Nissan Altima with the Check Engine Light On

The engine runs rough, gas mileage is down and more importantly the "check engine" light is on. That little illuminated check engine light strikes fear in the hearts and minds of the average vehicle owner - it's supposed to. Otherwise, people would keep driving their vehicles as long as they could, eclipsing the light with a piece of electrical tape.

The engine runs rough, gas mileage is down and more importantly the "check engine" light is on. That little illuminated check engine light strikes fear in the hearts and minds of the average vehicle owner – it’s supposed to. Otherwise, people would keep driving their vehicles as long as they could, eclipsing the light with a piece of electrical tape. That wouldn’t be good for our air quality. Luckily, most good citizens are of the belief that if that check engine light is on, not only is the vehicle going to leave them stranded at the most inopportune time, a plague could befall their entire family and their subsequent heirs for generations.

To the professional technician however, the "check engine" light is a sign that there may be a significant problem, but it’s probably nothing that’s going to change the course of history. With the help of ongoing education, a good scan tool and accurate diagnostic information, thousands of technicians repair "check engine" light related problems daily.

So why does something as simple as an engine misfire warrant a tech tip? Many techs assume that because automotive technology has become more complex, drivability problems have become more complex. In some ways they have, but on the other hand, sometimes facilitating a timely repair is just a matter of checking the simple basics.

In keeping with the simplicity theme, let’s cut straight to the details of this tech tip. If any of the applied vehicles (listed below) have a check engine light on, diagnostic trouble codes P0300 through P0304 (cylinder misfire) stored and/or exhibit a rough running engine, check the spark plug wire tubes and boots as follows:

Applied Vehicles:
• 1995-97.5 Altima (U13) models built before: 1N4BU31D3VC245368; and
• 1998 Altima (L30) models built before: 1N4DL01D8WC165916.

Applied Dates:
• 1995-97.5 Altima (U13) models built before March 5, 1997; and
• 1998 Altima (L30) models built before October 28, 1997.

PROCEDURE:
1. Remove the spark plug wires and inspect for water in the spark plug holes. If water is in the spark plug holes, perform the following steps:
• Remove water from the spark plug holes.
• Insert a paper clip through the steam vent hole in the spark plug wire boots to insure the holes are clear (see Figure 1).

NOTE: The steam vent hole allows water vapor to escape if water becomes trapped in the spark plug hole.

• Inspect spark plug wire boots for cracks, hardening or deformities that could prevent sealing between the boots and the camshaft (valve) cover.
• Replace all spark plug wires if one or more of the boots show signs of cracks, hardening or deformities.

If the spark plug holes are dry and the spark plug wire boots are in good condition, proceed with step 2.

2. Inspect the entire surface of each spark plug wire tube for pinholes and/or cracks (see Figure 2).

• If one or more spark plug wire tubes have pinholes and/or cracks, replace all of the spark plug wires.

And there you have it — in these complex times, a simple solution to a simple problem. And all that was required was an ongoing education, a good scan tool and accurate diagnostic information. It’s up to you to provide the first two items. As for the last item — I’m always glad to help.

Written by ALLDATA Technical Editor, Rich Diegle. Rich is an Advanced Engine Performance Certified and ASE Master Technician with an Associate of Arts degree in automotive technology and 22 years of dealership and independent shop experience.

For additional information, visit www.alldata.com.

You May Also Like

Ball Joints – How To Avoid Memory Steer

Follow all instructions to avoid issues caused by incorrect installation. This video is sponsored by Auto Value and Bumper to Bumper.

If your shop works on trucks like the Ford F 250 or Dodge Ram 2500, you know that these have a solid front axle. During their lifetime, chances are the ball joints will need to be replaced.

Trucks like these have ball joints because they're four wheel drive and the axle goes between where the kingpin used to be. When you're installing the two ball joints it's critical that they're installed on-axis. If they're installed off axis – in other words, one ball joint doesn't line up with the other – you could have issues with memory steer. When memory steer happens, the driver will notice that, as they're going around a corner and releasing the steering wheel, it may not return.

Sustainability And Automotive Batteries

Sustainability starts with you, and recycling is a great way to go green. This video is sponsored by The Group Training Academy.

PRT Releases 28 New Complete Struts in North America 

The new items represent nearly 6 Million vehicles in new coverage and come to expand the PRT portfolio in the North American Aftermarket.

Alternators and Ripple Voltage

The alternator produces an AC current that must be converted into DC current by way of a rectifier.

Mullen Announces EV Battery Exchange Program

POWER BOOST enables existing Class 1 EV cargo van customers the opportunity to upgrade their lithium-ion battery packs to solid-state polymer battery packs, increasing Class 1 vehicle range to over 200 miles.

Other Posts
Power Window Regulator and Motor Service

Power windows are great as long as they roll up and down when commanded to do so.

Toyota Invests in EV Charging Network IONNA

IONNA plans to install at least 30,000 charging ports in North America by 2030, and stations will include both NACS and CCS connectors to support all BEV drivers.

Hybrid & BEV Cooling System Maintenance 

Do they need coolant replacement?

Following AC System Service, How Much Oil Is Needed?

Learn how to determine the correct amount of oil to add when replacing the compressor in an AC system.