Jump Starting an EV

Jump Starting an EV

If an EV with a full battery won't start, here's how you can get it up and running.

Here’s a real-world scenario: A customer brings their EV into your shop for service, and it’s been there for quite a while because the parts are on backorder. After a few weeks, you get in the vehicle to move it out of your way, and the ignition won’t turn on. It’s acting like the battery is dead, so what do you do now?

High Voltage vs Low Voltage

Chances are that the low voltage (LV), or 12V, battery inside that EV has gone dead. In most cases, the LV battery is not charged while the high voltage (HV) battery is plugged into the wall charger. So, even if your shop is outfitted with an HV wall charger, the LV battery could still go dead if it’s left alone long enough.

This scenario can present a few unique challenges to us as techs or shop owners. The first question we need to ask ourselves is, “can I jump this EV with another car?” We would advise against this idea. It’s much safer to have a dedicated battery jumper, preferably one with some electronic assist to protect the system from surges, inverse polarity, etc. Compact battery jump packs are available, and are really handy for all kinds of situations.

Now you need to find the LV battery, and it could be anywhere in the vehicle. This of course will vary from one EV to the next, but the most common locations would likely be under the hood or in the trunk. But, herein lies another challenge – some EVs, specifically Teslas, have electronic door poppers which release the trunk and the hood (AKA the front trunk or frunk). So, it sort of turns into a “chicken before the egg” situation. How can you open the hood to get to the LV battery and jump it, if there’s no 12V power to actually open the hood?

Fear not, because Tesla thought this one out. There is a pair of wires that are located just behind the front tow hook cover in the front bumper cover (Figure 1). With a 12V battery jump pack on hand, press firmly on the top right perimeter of the tow hook cover until it pivots inward, then gently pull the raised section out toward you. Pull the two wires out of the tow eye opening and connect them to the jump pack: red positive (+) to red positive (+), black negative (-) to black negative.

Be aware that these wires are not a charging point for the LV battery. Applying 12V power to these wires will only pop the hood release, but now you can gain access to the LV battery inside. Open the hood and remove the trim panel which covers the LV battery. Locate the positive charge/jump post, and connect a suitable battery charger or jump pack to it. Attach the negative cable from the charger/jump pack to the beam in front of the LV battery (Figure 2). You should now be able to charge or jump the LV battery, and power on the ignition.

You May Also Like

USPS to Buy Six Canoo EVs

The Postal Service will take delivery of six right-hand drive versions of Lifestyle Delivery Vehicle 190 in Q1 2024.

Canoo announced the U.S. Postal Service will purchase six battery-electric Canoo vehicles. The Postal Service will take delivery of these six right-hand drive versions of the LDV 190 in Q1 2024. This electrification effort is part of the USPS’s $40 billion investment strategy to upgrade and improve the organization’s processing, transportation and delivery networks, the company said.

Belt Service For Hybrid and Stop/Start Systems

Knowing how to “force start” a hybrid vehicle can be helpful if you are trying to diagnose a noise problem that involves the accessory belt drive system.

Diesel Turbocharging Basics

There’s a reason diesels typically utilize compound turbo setups instead of twin turbochargers.

Batteries For Stop/Start Systems

On all stop/start vehicles, the life and performance of the battery are measured by the vehicle in several ways.

Power Window Regulator and Motor Service

Power windows are great as long as they roll up and down when commanded to do so.

Other Posts

Diagnosing Misfires

What if there are no codes and a misfire is intermittent? This is where it gets complicated.

Lifter Deactivation

The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine.

Diagnostic Procedures For Stop/Start Systems

Stop/start technology is more than just a switch wired to the brake pedal and starter.

Alternator Testing For No Charge Conditions

Many alternator problems turn out to be nothing more than a bad connection at the alternator or a bad wiring harness.