Kia Tech Tip: TCM Logic Revision – UnderhoodService

Kia Tech Tip: TCM Logic Revision

This bulletin provides information related to a logic change in the Transmission Control Module (TCM) for 2001 Rios, and 1998 through 2001 Sephia and Spectra vehicles built after Oct. 18, 2000.

This bulletin provides information related to a logic change in the Transmission Control Module (TCM) for 2001 Rios, and 1998 through 2001 Sephia and Spectra vehicles built after Oct. 18, 2000. On vehicles built before that date, under certain driving conditions the following DTCs may be stored without a true defect being present: P0705, P0740, P0731, P0732, P0733 and P0734.

TCMs in vehicles built after Oct. 18, 2000 use a revised diagnostic routine software to reduce the incidence of related DTCs. The revised TCM should be used to repair affected vehicles experiencing a repeat incidence of the above-mentioned DTCs.
Note: The part number for the revised TCMs did not change. However, all TCMs currently in PDC stock have the revised logic.

Preliminary:
• Familiarize yourself with the procedures outlined in TSB, Transmission/Driveline 003. Obtain an A/T diagnosis worksheet and fill it out as you proceed.

• Check the A/T fluid for level and appearance. If the fluid is burnt or contaminated, the transaxle may have to be replaced per the instructions in the TSB before proceeding.

• Check for any (pending) DTCs, record their description and freeze-frame data. If any electrical or circuit related DTCs are stored, repair them before replacing the TCM or before attempting to correct DTCs that indicate system malfunctions.

• On repeat repairs, always check the vehicle’s repair history to determine previous repairs and whether they were effective. Use the repair history as required to aid in your diagnosis and repair procedures.

Inspection:

  1. Open the driver’s door and check the production date on the FMVSS door label.
  2. If the vehicle’s production date is Oct. 18, 2000, or later, the vehicle already has the correct TCM; no TCM replacement is required. Note: If the TCM has previously been replaced on this vehicle, it’s possible that an older version was inadvertently installed. When in doubt, check the TCM version regardless of the vehicle production date.
  3. If the vehicle’s production date is before Oct. 18, 2000, determine if the correct TCM version has been used.
  4. If the TCM is found to be an early version, proceed with step 5. Note: If the TCM is the correct version, and DTCs are stored, follow the appropriate procedures using DTC-specific checklists in the service manual and/or DTC-specific tips/information in the scan tool.

Repair Procedure:

  1. Make sure the ignition switch is off and the gear selector is in the “park” position.
  2. Locate the TCM under the left lower dash area.
  3. Rio only: Loosen and remove the three mounting nuts that secure the ECM mounting bracket to the firewall (these are also used to secure the TCM).
  4. Rio only: Loosen and remove the one remaining nut that secures the TCM mounting bracket to the firewall.
  5. Sephia/Spectra: Loosen and remove the two nuts that secure the TCM mounting bracket to the firewall.
  6. Remove the TCM, release the wire harness connector locking lever, then disconnect the TCM from the wire harness. Discard the old TCM.
  7. Install the new TCM in the reverse order of removal.
  8. Test-drive the vehicle after warm-up and check for (pending) DTCs. If any (pending) DTCs set during the test-drive, investigate them and correct as required. Use flight record data and follow the appropriate procedures using DTC-specific checklists in the service manual and/or DTC-specific tips/information in the scan tool.

Courtesy of IDENTIFIX.

For additional information, visit www.identifix.com.

You May Also Like

FLO, GM Activate Plug and Charge for GM EV Drivers in Canada

FLO’s technology confirms identification, authorizes the charging session and activates billing without any additional action from the driver.

FLO and General Motors activated the Plug and Charge capability at all DC fast chargers on the FLO network across Canada. All GM EV drivers are provided with access to GM’s Plug and Charge, which is enabled by FLO’s autocharge software. The feature allows GM EV drivers to begin a fast-charging session by plugging in their vehicle at one of FLO’s fast charging stations across Canada, the company said.

Schaeffler and Sustainability with Jerry Conroy

Conroy shares insights into his career trajectory, the evolving landscape of the company’s aftermarket operations, and its commitment to innovation and sustainability.

Flushing the Brake Fluid is Critical on Every Brake Repair

Making sure the brake fluid is the correct quality is critical. Sponsored by Auto Value and Bumper to Bumper.

Selecting the Right Oil for your Customers Engine

Learn how to educate customers on the importance of OEM specifications and premium lubrication for their vehicles’ maintenance needs.

At the Intersection of Tradition and Innovation with Grace Hovis

Grace Hovis’s journey in Hovis Auto & Truck Supply blends tradition with digital innovation in the automotive aftermarket industry.

Other Posts

Inspection Tips For Chain-Driven Water Pumps

If one water pump fails sooner and is replaced without an investigation, the new pump is likely doomed.

Water pump feature
Power Window Regulator and Motor Service

Power windows are great as long as they roll up and down when commanded to do so.

Philips Announces GoPure GP5212 Automotive Air Purifier

It uses a 3-layer filter to deliver cleaner, healthier, fresher air on the go, Lumileds said.

Snap-on Announces Latest Software Release

The latest software includes new coverage and guided component tests and features.