Diagnostic Dilemmas: 8 Simple Rules … – UnderhoodService

Diagnostic Dilemmas: 8 Simple Rules …

Many of the "Diagnostic Dilemmas" Gary Goms is called upon to solve aren't really all that complicated - but were caused by basic oversights and incorrect assumptions on the part of the technician. This situation has largely been caused by a lack of training and, in some cases, poor training.

Since I began doing part-time mobile diagnostic work for local shops, I’ve noticed that most “Diagnostic Dilemmas” I’m called upon to solve aren’t really all that complicated.

Most of these Diagnostic Dilemmas were caused by basic oversights and incorrect assumptions on the part of the technician. This situation has largely been caused by a lack of training and, in some cases, poor training.

For example, when on-board diagnostics were popularly introduced in the early 1980s, many early trainers had to fill voids in OEM information by gathering information from anecdotal sources. But, in hindsight, much of the information provided 20 years ago has been proven incorrect.

Unfortunately, the incorrect information and incorrect assumptions developed 30 years ago is still part of our diagnostic dialogue. In most cases, they fall into one of eight categories of common diagnostic mistakes.

photo 1: to solve for amps, cover the ampere portion with your finger and divide voltage by resistance. a circuit operating at 14.2 volts against a resistance of 2 ohms will, for example, carry 7.1 amperes of current.1. Skipping the Customer Interview
The most common mistake of service writers and technicians is assuming that any problem can be diagnosed by simply retrieving a trouble code. For that reason, many service writers fail to determine the actual customer complaint or gather the background information needed to quickly and efficiently address the problem.

To illustrate, last spring I was called to solve a cold-stalling problem on a 2005 Jeep Wrangler. The PCM had stored at least one throttle sensor-related DTC and, following a service bulletin on that particular failure, the shop had removed the driver’s air bag to test the cruise control circuits.

I won’t explore this issue since it became apparent that it wasn’t directly related to the stalling complaint. But it did momentarily divert my attention away from the immediate problem of the engine cold-stalling until it had warmed up for about one minute. After a short warm-up, the engine started and idled perfectly for the rest of the day. My first impression was a fuel quality problem, but I set that theory aside for the moment because fuel quality hasn’t been a problem in my community during the past eight years.

photo 2: assuming the resistance (ohms) remains the same, volts and amperes are inseparable components of any 
</p>
</p>
	</div><!-- .entry-content -->

		<div class=

You May Also Like

Belts and Pulley Alignment

A misalignment of the plane of the belt can occur when a pulley is not parallel to the other pulleys on the belt drive system.

Drive Belt Alignment Alignment is key to the health of an engine belt. The belt drive system is designed to create friction between the grooves on the belt and pulley to transfer power from the crankshaft to the alternator, water pump or power steering pump. If the grooves on the belt do not align with the pulleys, the friction won’t be evenly applied and can result in wear and noise.

ECM Damage

Engineers have devised two strategies that can be called the “immune system” for the electrical system.

Voltage Drop Testing

The measurement of voltage is like the speed of the traffic.

Spark Plug Fouling

Understanding why spark plugs get dirty.

Understanding Stop/Start Charging and Starting Systems

The problem may not have been caused by a complicated reason, something simple may have caused the system not to work.

Other Posts

Hybrid Vehicle Fluid Maintenance

There are opportunities your shop can’t pass up just because the car or SUV has a hybrid badge on the back.

Ignition Coil Output

To see inductance inside the primary windings, use an amp probe placed around the positive wire for the ignition coil.

Caring For AGM And Flooded Car Batteries

Faulty battery cables, if loose, corroded, or damaged, can lead to power drainage.

Power Window Regulator and Motor Service

Power windows are great as long as they roll up and down when commanded to do so.