Tech Tip: GM Vehicle has DTC P0757 Set, MIL Illuminated and Slipping Transmission – UnderhoodService

Tech Tip: GM Vehicle has DTC P0757 Set, MIL Illuminated and Slipping Transmission

Some customers may comment on any of the following conditions - an illuminated MIL (where DTC P0757 is found as a history code), no third and fourth gear and the the transmission does not shift correctly.

Models affected:
– 2007 and prior GM Passenger Cars and Light Duty Trucks;
– 2003-’07 HUMMER H2;
– 2006-’07 HUMMER H3; and
– 2005-’07 Saab 9-7X
with 4L60-E/4L65-E/4L70-E Automatic Transmission (RPOs M30/M32/M70).

Figure 1Some customers may comment on any of the following conditions:
• An illuminated MIL where DTC P0757 is found as a history code in the PCM or TCM;

• No third and fourth gear;

• The transmission does not shift correctly;

• The transmission feels like it shifts to Neutral or a loss of drive occurs; and/or

• The vehicle free wheels above 30 mph. High rpm needed to overcome the free wheeling.
This condition may be caused by any of the following:

• Chips or debris plugging the bleed orifice of the 2-3 shift solenoid (367). This will cause the transmission to stay in second gear when third gear is commanded and return to first gear when fourth gear is commanded.

• A 2-3 shift valve (368) or 2-3 shuttle valve (369) that is stuck, restricted and/or hung-up in its bore.

This condition may also be an indication of a damaged 2-4 band or 3-4 clutches. This clutch damage may generate debris causing the 2-3 shift valve line-up to stick in the valve body bore and set DTC P0757.

1. Inspect the condition of the transmission fluid for signs of overheat or a burnt odor. If either is noted, the transmission should be disassembled for further investigation and repaired as needed.

See Figure 1.

2. Inspect the inside of the oil pan for signs of clutch friction material. A small amount of friction material in the bottom of the pan is normal. If a large amount of clutch material is noted in the fluid or bottom pan, the transmission should be disassembled for further investigation and repaired as needed.

3. Inspect and clean the 2-3 shift valve (368), the 2-3 shuttle valve (369) and the valve bore of debris/ metal chips.

4. Inspect and clean the 2-3 shift solenoid (367B) opening of debris/metal chips. While inspecting the 2-3 shift solenoid (367B), look for a screen over the solenoid opening. If the solenoid does not have a screen, replace the solenoid. All current GMSPO stock shift solenoids have a screen over the solenoid opening.

5. If clutch debris is found, it is also important to inspect the pressure control (PC) solenoid valve fluid screens. Clean or replace the PC solenoid as necessary. It is also important to flush and flow-check the transmission oil cooler using J 45096.

Refer to SI “Automatic Transmission Oil Cooler Flushing and Flow Test” for the procedure.

Refer to the appropriate service manual for additional diagnostic information and service procedures.

Courtesy of Mitchell 1.

You May Also Like

Belts and Pulley Alignment

A misalignment of the plane of the belt can occur when a pulley is not parallel to the other pulleys on the belt drive system.

Drive Belt Alignment Alignment is key to the health of an engine belt. The belt drive system is designed to create friction between the grooves on the belt and pulley to transfer power from the crankshaft to the alternator, water pump or power steering pump. If the grooves on the belt do not align with the pulleys, the friction won’t be evenly applied and can result in wear and noise.

Diagnosing Misfires

What if there are no codes and a misfire is intermittent? This is where it gets complicated.

Lifter Deactivation

The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine.

Alternator Testing For No Charge Conditions

Many alternator problems turn out to be nothing more than a bad connection at the alternator or a bad wiring harness.

Understanding Coolants

All-season coolant used inorganic acid technology and worked great for almost 30 years.

Other Posts

Ignition System Do’s and Don’ts

Why do ignition systems give technicians problems when diagnosing ignition-related misfires? The answer is that some technicians use tests that might give inconclusive results or do damage to the coil or drivers inside a module.

Tools To Service Serpentine Belts

Servicing the serpentine belt on some vehicles is a tough task.

Battery Charging and Diagnostics

Here are six tips to use when diagnosing a vehicle with a dead battery. 

Why Do Timing Chains Stretch?

As the timing chain wears, it can change the timing of the camshaft and crankshaft.