Tech Tip: Kia Optima’s MIL Is On With DTC P0123 Set – UnderhoodService

Main Navigation

Advertisement
Social Connect
Resources
Our Brand Family
Underhood Service Logo
Technical resources to help diagnose and repair engine-related service issues.
Engine

Tech Tip: Kia Optima’s MIL Is On With DTC P0123 Set

This bulletin provides information relating to an engine hesitation or the illumination of the Malfunction Indicator Lamp (MIL) for P0123 (Throttle Position Sensor/Switch "A" Circuit High Input). Improper throttle position sensor (TPS) values may cause the engine to hesitate under loads or cause the illumination of the MIL. To correct this condition, the TPS has been improved.

Underhood Service Staff Writers
By Underhood Service Staff Writers
Published:

Affected Vehicle Range:

Related Articles

• 2001-’06 Optima (MS) equipped with 2.5L/2.7L (V6) Delta engine (produced between Oct. 17, 2000 and Aug. 31, 2005)
• 2005-’07 Sportage (KM) equipped with 27L (V6) Delta ­engine (produced between Oct. 28, 2004 and May 18, 2007)

Repair Procedure:

1. Turn the ignition key to the Off position. Open the hood and remove the engine cover. Disconnect the VIS (Variable Induction System) connector and the injector connector, if equipped. See Fig. 1.
fig. 1
2. Disconnect the idle speed control actuator (ISCA) connector and remove the two retaining bolts. ­Remove the ISCA and gasket.

3. Disconnect the TPS connector and remove the two mounting screws.

4. Install the new TPS sensor onto the throttle body and torque the two screws (1.5-2.5 Nm/13.2-21.6 in.-lbs.). Reconnect the TPS connector. See Fig. 2.
Fig. 2
5. Install a new ISCA gasket and re-install the ISCA actuator. Torque the ISCA bolts (6-8 Nm/52.8-69.6 in.-lb.) and reconnect the ISCA connector. Reconnect the VIS connector and the injector connector, if equipped.

6. Reinstall the engine cover.

Courtesy of ALLDATA.

You May Also Like

Engine

Belts and Pulley Alignment

A misalignment of the plane of the belt can occur when a pulley is not parallel to the other pulleys on the belt drive system.

Andrew Markel
By Andrew Markel
Andrew Markel is the director of content for Underhood Service magazine. He has been with Babcox Media for 20 years. He is a technician and former service writer and holds several automotive certifications from ASE and ­aftermarket manufacturers.
Published:

Drive Belt Alignment Alignment is key to the health of an engine belt. The belt drive system is designed to create friction between the grooves on the belt and pulley to transfer power from the crankshaft to the alternator, water pump or power steering pump. If the grooves on the belt do not align with the pulleys, the friction won’t be evenly applied and can result in wear and noise.

Read Full Article

More Engine Posts
Diagnosing Misfires

What if there are no codes and a misfire is intermittent? This is where it gets complicated.

By Andrew Markel
Lifter Deactivation

The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine.

By Andrew Markel
Alternator Testing For No Charge Conditions

Many alternator problems turn out to be nothing more than a bad connection at the alternator or a bad wiring harness.

By Andrew Markel
Understanding Coolants

All-season coolant used inorganic acid technology and worked great for almost 30 years.

By Andrew Markel

Other Posts

Ignition System Do’s and Don’ts

Why do ignition systems give technicians problems when diagnosing ignition-related misfires? The answer is that some technicians use tests that might give inconclusive results or do damage to the coil or drivers inside a module.

By Andrew Markel
Tools To Service Serpentine Belts

Servicing the serpentine belt on some vehicles is a tough task.

By Andrew Markel
Battery Charging and Diagnostics

Here are six tips to use when diagnosing a vehicle with a dead battery. 

By Andrew Markel
Why Do Timing Chains Stretch?

As the timing chain wears, it can change the timing of the camshaft and crankshaft.

By Andrew Markel