Tech Tip: Silverado Owner Complains that ABS Light Comes on at 40-50 mph – UnderhoodService

Tech Tip: Silverado Owner Complains that ABS Light Comes on at 40-50 mph

At speeds over 40-50 mph, the ABS and brake indicators come on, and the fuel and volt gauges sometimes drop low at the same time. The technician had already verified the condition and checked for codes before calling Identifix. He found code C0237 (rear wheel speed signal erratic) stored as a history code, but it had not reappeared for him. Next he road-tested with a scanner, watching the vehicle speed input through the powertrain control module (PCM) and electronic brake control module (EBCM) data. When the ....

Vehicle: 1999 Silverado.

Customer Complaint: At speeds over 40-50 mph, the ABS and brake indicators come on, and the fuel and volt gauges sometimes drop low at the same time.

The technician had already verified the condition and checked for codes before calling Identifix. He found code C0237 (rear wheel speed signal erratic) stored as a history code, but it had not reappeared for him. Next he road-tested with a scanner, watching the vehicle speed input through the powertrain control module (PCM) and electronic brake control module (EBCM) data. When the ABS and brake light came back on, data was lost on the scanner for both the PCM and ABS. Something was crashing the class 2 data line — but what?

On this truck, the instrument panel cluster (IPC), body control module (BCM), EBCM, PCM and automatic transfer case control module (ATC) are all on the class 2 data line at pin 2 of the data link connector. The tech went to the splice pack (SP205) to determine which module was initially causing the problem. The splice pack joins all of the data circuits at one point, and is located on the lower left side of the dash behind the headlamp switch. The splice pack, a connector end with a jumper bar seated into it, is located on a short harness and often is taped to another harness. When the EBCM class 2 data wires were disconnected from the data line, the symptom was gone. Now we knew the EBCM circuit was causing the problem, so that left either a problem with the power/ground or the EBCM.

The tech checked the connector at the EBCM for corrosion and terminal condition — it was OK. Next he removed and cleaned the ground for the EBCM at the frame (see GM bulletin #04-05-25-002A). Using a headlamp to load the circuit, he load-tested the power and ground to the EBCM. The power and ground tested OK, but there was still a problem. A new EBCM fixed this one.

Written by IDENTIFIX GM Specialist Bill Siegmann. Bill is certified ASE Master and L1 with 20 years of diagnostic and repair experience.

For additional tech tips, visit www.identifix.com.

You May Also Like

Check Out The December Issue Of Underhood Service Magazine

The digital version of the December issue of Underhood Service is available on-line. Access the easy-to-view digital version that features articles on Spark Plug Service, Hyundai Oxygen Sensor Codes, CAN Bus Diagnostics, Subaru Stretch Belt Replacement, a host of Tech Tips, and more!

The digital version of the December issue of Underhood Service is available on-line.

CLICK HERE to access the easy-to-view digital version that features articles on Spark Plug Service, Hyundai Oxygen Sensor Codes, CAN Bus Diagnostics, Subaru Stretch Belt Replacement, a host of Tech Tips, and more!

Transmission Line Replacement

Transmission fluid likes to be at a constant temperature. If it is too hot or too cold for too long, the performance can fluctuate and potentially cause damage to the transmission.

VIDEO: AAPEX 2016 Insights

Andrew Markel discusses his take on conversations he had with economists at AAPEX 2016, including the future of purchasing parts.

BMW Tech Tip: Oil Separator Replacement

A clogged oil separator valve is a common problem on many BMW DOHC inline sixes. The high failure rate is caused by sludge build-up that can result in oil burning, rough idle and engine fault codes. Although the solution is pretty simple, replacing the valve is labor intensive and can take anywhere from six to nine hours.

New IDUSA Premium Guard Website Offers Easy Access To Wide Range Of Oil, Air, Cabin, Fuel And Transmission Filters

The new website’s bi-lingual, responsive design features look-up powered by ShowMeTheParts.

Other Posts

VIDEO: What Happens When An ABS WSS Fails?

Common wheel bearing failures and the resulting codes. This video is sponsored by BCA Bearings by NTN.

VIDEO: Setting The Air Gap For Wheel Speed Sensors And ABS

You should never remove the wheel speed sensor from a new wheel hub. Here’s why. This video is sponsored by GMB.

ABS Fault Code 02757 Diagnosis Tip

Models: 2011-2014 Jetta, Jetta Sportwagen, Golf/GTI, Tiguan, Eos, 2012-2014 Beetle, Passat.

Toyota Tech Tip: ABS Noise, Warning Lamps And Code C1431

Some 2012-’13 model year Camry vehicles may exhibit a condition where ABS brake actuator pump motor noise is heard from the engine compartment with Brake ABS and/or TRAC warning lamp(s) illuminated and DTC C1431 stored. A poor ground on the left fender side panel bracket may cause this condition after a collision repair.