Tech Feature: Steering Gear Diagnostics – UnderhoodService

Tech Feature: Steering Gear Diagnostics

We need to understand the basics of how a power steering system works before we can develop an assessment technique. At its most basic level, the steering system's power steering pump can generate up to 2,000 psi of hydraulic pressure. This hydraulic pressure is metered to a steering assist cylinder through a steering gear pressure control valve. Both the cylinder and valve are integral to the steering gear assembly on modern vehicles.


Some systems also incorporate a reaction disc at either end of the steering pinion or worm gear. As the steering gear changes direction, one of the reaction discs compresses as torque is applied to the steering wheel. Here again, the steering control valve responds to the movement of the steering pinion gear to help modulate the flow of oil into the assist cylinder.

When assessing a power steering complaint, it’s ­important to consider the complete system. If, for ­example, the steering pump is worn out, the system hydraulics will likely be full of metallic particles. Worn steering hoses can similarly shed material into the oil stream, which can cause steering-assist complaints due to clogging of the steering control valve ports. Hardened or deteriorated hoses can also potentially develop ­internal stress faults after they’ve been reinstalled. It’s always better to recommend new hoses to go with the new power steering pump or steering rack, and a thorough flushing of the system, when any major part is replaced.


A dry park test is performed with the transmission in “park” and the front wheels on the ground. After starting the engine, check for a “bump” or movement in the steering wheel as the engine starts (see Photo 1).

If movement is detected, the power steering gear might have developed an unequal steering assist in one direction or the other. Next, check for a smooth power assist. If the assist is uneven or jerky, inspect the power steering pump fluid level and check the drive belt condition and adjustment. If the fluid level is low, check for leaks at the pump, hoses or the steering gear or rack oil seals. If the belt is worn or glazed, it should be replaced (see Photo 2).
photo 2: always begin an under-hood inspection by checking power steering fluid level, color and viscosity.
When turning the steering wheel several times from lock to lock, power assist should feel even from side to side and the steering wheel should feel immediately responsive to changes in direction. Keep in mind that binding strut support bearings or seized ball joints can cause the steering to feel heavy and unresponsive.  If the right-to-left and left-to-right assist isn’t equal, the steering gear’s control valve system could be at fault. If there’s excessive play in the steering wheel, inspect the steering shaft universal joint, steering gear, steering gear mounts and steering linkage for looseness and wear (see Photo 3).
photo 3: always inspect the ­universal joint for wear and loose bolts. a flexible “rag” joint like the one at right can ­deteriorate  with age.
When the steering gear reaches full lock, a hissing noise usually indicates that the oil pressure bypass is limiting the pump’s maximum pressure. If the drive belt squeals at full lock, the belt is slipping due to wear or incorrect adjustment.

The exception to the above tests might be a power steering pump in which the Powertrain Control Module (PCM) controls oil pressure through a pulse-modulated pressure control valve on the steering pump. Because a variable-assist system responds to vehicle speed and other driving conditions, the diagnostics vary ­according to application. Always test for trouble codes stored in the PCM and check scan tool menus for available data and performance tests on any modulated system.


Because the steering pump is obviously the heart of the power steering system, always begin by checking the power steering fluid level. If the level is low, we could assume that the system is leaking fluid.

Next, it’s important to check the color and viscosity of the fluid. Normal color is red- or straw-colored. Blackened fluid might indicate that the hoses are ­deteriorating or that the power steering pump itself is worn. If the fluid appears extremely viscous, the fluid might have been contaminated with motor oil or other lubricant. If the fluid has an odd odor, it’s possible that an inexperienced technician has added brake fluid to the reservoir. In any case, if the fluid appears contaminated, the system needs a thorough flushing with the specified fluid (see Photo 4).
photo 4: the various symbols on this cap ­indicate that the reservoir contains power steering fluid and how to read the fluid level. the “caution” sign indicates that the owner’s manual contains a ­specific fluid ­recommendation.
Check the steering assist again after the pump and fluid warms up. If the pump produces noticeably less assist when hot, it’s probably worn. If the pump is noisy, check the fluid for foaming. If the fluid is foaming, it might be contaminated and the system might require flushing to correct this condition.

Although it’s rare, internal leakage inside the steering assist cylinder can’t be discounted if steering assist deteriorates as the fluid warms up. At this point, it’s best to recommend pressure-testing the steering pump. Of course, gaining access to the high-pressure hydraulic connections at the power steering pump or steering gear can be difficult, if not altogether impossible, on modern engines. Because testing is application-specific, it’s important to have manufacturer’s specifications at hand before recommending a pressure test to your customer.


Conventional steering gears are extremely reliable and most of the failures involve leakage around the steering shaft and sector shaft seals. In high-mileage cases, the steering gear might be slightly worn and require a sector shaft adjustment to remove excessive steering wheel play. With the engine running and a helper rocking the steering wheel, observe the end play at the steering shaft. Keep in mind that the steering shaft is pushing against its reaction discs, so the shaft should move in or out about 1/16 of an inch as the steering wheel is slowly rocked right and left.  

Similarly, watch the movement in the output or sector shaft. If the sector shaft bushings or housing are worn, the sector shaft will tend to move for and aft as the steering wheel is slowly rocked right and left. In addition, if the sector shaft has excess end-play, it will show a polished ring around the shaft at the seal contact point. In most cases, a simple sector shaft adjustment will restore the gear to normal operation.

When adjusting the sector shaft end-play in-chassis, make sure the steering is centered at the “high point” on the steering gear with the Pitman arm pivot points parallel to the frame and the steering wheel correctly indexed to its shaft. The sector shaft adjusting screw should be turned in until end-play is removed. Unless otherwise specified, a good rule of thumb is, before tightening the lock nut, back the adjustment screw out one-half turn to allow for heat expansion. When properly adjusted with the steering linkage disconnected, the steering gear should have a slight amount of play on either side of the steering gear high point. The gear should easily rotate through the high point, but the high point itself should not exhibit play in the steering wheel.


With the vehicle on a lift, grasp the tire at the 9 and 3 o’clock positions and rock the wheel in and out. If a clicking noise is heard, the inner tie rod end is probably worn where it connects to the steering rack. While we’re looking at the steering rack, check for external oil leakage at the boots and also feel the boot to see if it’s filled with oil (see Photo 5).
Photo 5: Always squeeze steering rack boots to see if they’re filled with oil. Boots that are torn should be ­immediately ­replaced.
If the boot is full of oil, the rack seals are leaking and the rack should be replaced. Because loose steering rack mounts will cause steering wander, it’s important to inspect the mounts for deterioration. Now that we’ve completed our “non-invasive” testing procedure, it’s time to make the appropriate service recommendations to the customer.

You May Also Like

Nearly 5,000 To Participate In Auto Value, Bumper To Bumper ‘Festive Walk’ To AAPEX 2018

On Thursday, Nov. 1, nearly 5,000 Auto Value and Bumper to Bumper automotive professionals wearing matching yellow shirts will begin their “festive walk” from the Mirage hotel to AAPEX 2018 at the Sands Expo, temporarily shutting down the busy Las Vegas Boulevard along the way.

On Thursday, Nov. 1, nearly 5,000 Auto Value and Bumper to Bumper automotive professionals wearing matching yellow shirts will begin their “festive walk” from the Mirage hotel to AAPEX 2018 at the Sands Expo, temporarily shutting down the busy Las Vegas Boulevard along the way.

The group is scheduled to depart at approximately 8:30 a.m. (PDT) and start arriving at AAPEX for their day-long visit around 9 a.m. The group will include parts store operators, shop owners, technicians and service writers who are part of the Aftermarket Auto Parts Alliance. Las Vegas showgirls and a marching band will join in the festivities as the group makes its way to AAPEX.

Drive Belt Checklist: What Are You Missing?

You might have only one chance to sell a customer a new serpentine belt. With belts lasting roughly 90,000 miles, proper inspection at the time of failure is critical not only for selling the belt, but also for ensuring add-on sales and better customer satisfaction.

3 Reasons To Replace Cabin Air Filters In Winter

Often driven by an “out of sight, out of mind” mentality, most consumers don’t think about purchasing cabin air filters. That’s why educating consumers on the benefits of cabin air filters can be a shop’s best sales pitch for selling these maintenance add-ons.

VIDEO: Using Airflow To Sell Cabin Air Filters

Andrew Markel introduces an inexpensive tool that can assist in selling cabin air filter replacements. Sponsored by Auto Value and Bumper to Bumper.

Air Conditioning Odor Causes

Air conditioning odors typically result from the uncontrolled growth of bacteria and other microorganisms in the evaporator. Research by independent laboratories has found fungi such as Aspergillus, Cladesporium, Penicillium and others growing on cooling coils and other A/C system areas.

ac air conditioning smells featured

Other Posts

Dorman Launches 300+ New Products In November

Among the new products is an OE FIX climate control module designed to fit 1.7M Chevrolet Express & GMC Savana vehicles.

Curing Springtime Air Conditioning Smells

Air conditioning scents can come from a host of things.

Steer Into the Future with Delphi Technologies by Your Side

Your vehicle’s steering and suspension is what not only ensures a smooth ride, but also its handling and safety. With over 98% vehicle coverage and trusted by over 26 major global OEMs, Delphi Technologies’ 8,000+ steering and suspension products are intelligence in engineering at its finest. Premium parts without the premium price tagAt Delphi Technologies,

Steering Systems Have Changed – Do Customers Care?

Power steering systems aren’t the same old same old. This video is presented by The Group Training Academy.