Chrysler’s Totally Integrated Power Module

Chrysler’s Totally Integrated Power Module

The TIPM is on the CAN bus, any issues with the communication between the ECM, ABS and BCM can cause problems with the TIPM.

TIPM is a fuse box, relay box and electronic module all in one. The electronic module is connected to several data networks.  For engineers, the module reduces a lot of wiring under the hood and passing through the firewall. The TIPM also increases the functionality of a component by allowing several inputs to control one component. 

Think about something as simple as a horn. The horn honks when the driver hits the button in the center of the steering wheel, or it might honk as part of the anti-theft system. 

Engineers could put a switch on the steering along with the wiring through the steering column and to a relay and eventually the horn. For the anti-theft horn circuit, it would require a wire going from the anti-theft module to a relay and maybe a separate horn. But on a system with a TIPM, the circuit is simplified, and the physical inputs going from inside the vehicle turn into commands over a network from modules to the TIPM that is connected to a relay and component. This architecture can be used for a fuel pump that requires several inputs from the ECM and anti-theft module to operate.

The symptoms of a failing TIPM can vary depending on the vehicle. For one car, it might be an inoperative horn or wipers. For some cars, it might be a no-start condition and erratic instrument cluster operation. A failure can be a no-crank condition. 

But, a lot of the symptoms match the failure of a starter or fuel pump. You might end up throwing a lot of parts at a vehicle when the root cause might be the TIPM.

Triage

The most important part of a TIPM diagnosis is to interview the customer and then replicate the symptoms in the bay or on a test drive. The next most crucial step is to scan all the modules on the vehicle for codes. 

The TIPM is on the CAN bus, any issues with the communication between the ECM, ABS and BCM can cause problems with the TIPM.

The next is to look at the module under the hood. Do not remove the TIPM; treat it like a crime scene. Carefully inspect for any physical damage and water intrusion.

The first step is to determine if the inputs from switches and modules are present. For example, most wipers on Chryslers with a TIPM module have the relay that sends power to the motor. When the driver turns on the wipers, the steering control module sends a signal to the TIPM using a serial data bus. The TIPM then sends a command signal to the wiper relay. If the wiper motor is working, the arms move.

The pathway for the actuation of the fuel pump and power windows are very similar. Before condemning the TIPM, it is critical to look at the circuit, controls and actuated component.   

There are two ways a TIPM can fail. First, the TIPM’s electronic module can fail to operate and send out power to the control side of the relays. It can also lose the ability to communicate with other modules on the vehicle. When this happens, you might have codes in the TIPM and additional modules for loss of communication codes.

In these cases, you can use a scan tool to see the data stream change when a switch is pressed or when the key is turned. The data can be observed in both the module requesting the command and the TIPM. It is also critical to verify the operation of the component by powering the component with an external power source. 

The TIPM contains the fuses and relays. Some of the relays are removable and can be tested for power and control. You can also confirm if there are good grounds. 

There are other relays contained deep inside the TIPM. These are soldered to circuit boards. But, these circuits have fuses for testing with an amp current probe. When these relays fail, it could mean complete TIPM replacement.

Before you replace the TIPM, remove the unit and inspect the connections. If there is any damage to the connections and green crust around terminals, try cleaning the terminals. The problem might be resolved, but damage may have already occurred to the TIPM due to high resistance in the circuit.

But, there are other strategies for TIPM repair besides replacement. If the fuel pump circuit has failed and the pump runs constantly, it is probably the fuel pump relay circuit. Some kits allow technicians to create a bypass around the relay in the TIPM. You can also attempt to solder a new relay onto the board.  

If a TIPM needs to be replaced, there are several options that were not around a decade ago. Aftermarket suppliers have new and remanufactured TIPM modules. Also, there a specialist rebuilders of TIPMs.

You May Also Like

Chassis Control Modules After Reconnecting Battery

To resolve the issue, fully disconnect the negative lead from the battery terminal.

Models: XJ/X351, XF/X250 with air suspension

Issue: If the battery supply to the vehicle is disconnected for any reason, the Chassis Control Module (also known as the Air Suspension Module or Suspension Module Integrated Suspension Control Module (CHCM) may not power-up correctly. As a result, a scan tool will report no communication with the CHCM module in several session screens. This will only affect a small percentage of cars and on an intermittent basis.

Reflashing Power Supplies

A power supply to keep the system voltage consistent is a required piece of equipment to perform a reflash procedure.

BMW Transfer Case Service

The transfer case is a rather unique design in the way that it operates a clutch pack mechanically, not hydraulically.

Today’s Fuel Pressure Diagnostics

Direct injection pressure is measured with sensors, and you’ll need a scan tool to measure the signals

OBDII Connectors

OBDII connectors serve as the main communication point between the technician and the vehicle.

Other Posts

Diesel Air Filter Replacement

Here are some diesel air filter replacement tips in order to keep these vehicles running as intended.

Belt Service For Hybrid and Stop/Start Systems

Knowing how to “force start” a hybrid vehicle can be helpful if you are trying to diagnose a noise problem that involves the accessory belt drive system.

Ignition System Do’s and Don’ts

Why do ignition systems give technicians problems when diagnosing ignition-related misfires? The answer is that some technicians use tests that might give inconclusive results or do damage to the coil or drivers inside a module.

Charging for Diagnostic Time

Diagnostic work is more sophisticated and your techs’ time is worth charging for. This video is sponsored by Auto Value and Bumper to Bumper.