TPMS Update: FORD Tire Pressure Monitoring Systems – UnderhoodService

TPMS Update: FORD Tire Pressure Monitoring Systems

Ford embraced Tire Pressure Monitoring Systems (TPMS) as early as the 2002 model year on the Explorer and Windstar. These systems can be can be direct or indirect. All 2007 models have TPMS standard. From 2006-2009, Ford used banded sensors that are mounted in the center of the rim. In 2010, Ford reverted to the valve stem mounted sensors. All the systems are straightforward and use common procedures for most models.

v>

8. Repeat Step 7 for the RR, LR and spare tire.
When the tire training procedure is complete, the horn will sound twice and the message center will display “TIRE TRAINING MODE COMPLETE.”
2006-2011 (2005 Escape, Edge and Mariner)
TPMS was standard for the 2007 model year. 2007-2009 models have banded sensors, while most 2010-2011 models have sensors mounted behind the valve stem.
 
If the vehicle has been stationary for more than 30 minutes, the sensors will go into a “sleep mode” to conserve battery power. It will be necessary to wake them up so they will transmit the latest tire pressure information to the Smart Junction Box (SJB).
Activation
1. Turn the ignition switch to the ON position.
 
2. Position the TPMS tool against the LF tire sidewall, 180 degrees from the tire valve stem. The TPMS tool must remain in place 180 degrees from the valve stem for 2007-2009 models with banded sensors and directly below the valve stem on the sidewall for 2010-2011 models with the valve stem mounted TPMS sensors.
 
3. NOTE: The TPMS tool will provide feedback in the form of a flashing green light and a beep sound for each successful response from a tire pressure sensor. Press the test button on the TPMS tool to activate the sensor. Activate the sensor at least two times.
 
4. Repeat Steps 2 and 3 for the remaining tires.
Relearn
 
1. Turn the ignition switch to the OFF position. Then, press and release the brake pedal.
 
2. Cycle the ignition switch from the OFF position to the RUN position three times, ending in the RUN position.
 
3. Press and release the brake pedal.
 
4. Turn the ignition switch to the OFF position.
 
5. Turn the ignition switch from the OFF position to the RUN position three times, ending in the RUN position.
The horn will sound once and the indicator will flash if the training mode has been entered successfully. If equipped, the message center will display “TRAIN LF TIRE.”
 
6. It may take up to six seconds to activate a tire pressure sensor. 
Press and release the test button on the TPMS tool. The horn will sound briefly to indicate that the tire pressure sensor has been recognized by the vehicle.
 
7. Within two minutes of the horn sounding, place the TPMS tool on the correct position for the sensor and release the test button to train the right front tire pressure sensor.
8. Do not wait more than two minutes between training each sensor or the Smart Junction Box (SJB) will time out and the entire procedure must be repeated. Repeat Step 7 for the right rear and then left rear.
The procedure is completed after the last tire has been trained. When the training procedure is complete, the message center (if equipped) will display “TIRE TRAINING COMPLETE.”
 
For vehicles not equipped with a message center, successful completion of the training procedure will be verified by turning the ignition switch to the OFF position without the horn sounding. If the horn sounds twice when the switch is turned to the OFF position, the training procedure was not successful. 

You May Also Like

Ford Adaptive Cruise Control Alignment Process

Follow these steps for proper horizontal alignment of the cruise control module radar sensor.

• 2010-2017 Taurus, Explorer, Edge, Flex, Fusion, MKS, MKX, MKT, MKZ

• 2015-2017 F150, Mustang, and MKC 

• 2017 Super Duty, Escape, and Continental

This is information on setting up and completion steps for proper horizontal alignment of the cruise control module (C-CM) radar sensor.

Chrysler’s Totally Integrated Power Module Simplifies Circuits

The symptoms of a failing TIPM can vary depending on the vehicle. Check out your options for this repair.

Trakmotive Tech Tip: Window Regulator Installation

Here are eight tips to make your next window regulator replacement easier.

Multi-Spark Ignition Systems

You may have seen the stories about plasma or laser ignition systems that promise to give new life to the internal combustion engine. But while these ignition systems have yet to make it to market the latest ignition innovation still uses a coil and spark plug.

VIDEO: How Modules Manage Alternator Power

Andrew Markel discusses power flow through the electrical system on a vehicle, and how the modules help provide the right amount of power to different components. Sponsored by Valeo.

Other Posts

Beyond the Warranty

What does it take to keep a car going for 120,000, 180,000 or 250,000 miles? The key is maintenance and inspection. 

GM No Crank After Auto-Stop Event

These concerns could be caused by a broken or loose engine ground cable/strap, which grounds the engine to the body.

Caring For AGM And Flooded Car Batteries

Faulty battery cables, if loose, corroded, or damaged, can lead to power drainage.

Power Window Regulator and Motor Service

Power windows are great as long as they roll up and down when commanded to do so.