Fuel Tanks and Pumps

Fuel Tanks and Pumps

The behavior of the fuel wells, pumps & sending units are often misdiagnosed, leading to fuel pumps being replaced.

Automakers have installed saddle-style tanks on several car models for more than a decade. This style of tank uses two wells, one on either side of a driveshaft or exhaust system. On the bright side, this position optimizes luggage compartment capacity, fuel volume and crash safety. However, the behavior of the fuel wells, pumps and sending units are often misdiagnosed, leading to fuel pumps being replaced unnecessarily.

Basics

From the top, a saddle-style tank looks like one fuel tank. From the bottom, you will see two tanks. On most applications there will be a primary side that will have the pump that provides pressure to the fuel rail. This is typically the side that the fuel inlet fills first. The primary side usually uses a fuel pump module that connects to the vehicle over a serial data bus. The secondary tank contains a transfer pump, sometimes called a jet pump. 

Almost all modern saddle-style tanks use a returnless fuel system that regulates the pressure to the fuel rail inside the tank. Older systems with a return line may use a suction jet that uses a venturi effect created by the returning fuel to suck fuel into the primary fuel well.  

Both the primary and secondary wells contain fuel-level sender units. These are used to determine the fuel level in the tanks for fuel distribution, instrument panel readings and EVAP testing.

Fueling

During fueling, the primary side of the tank fills up first. Fuel then moves through a connecting passage to fill the secondary side. The transfer pump may be active on some systems during fueling.

When testing the operation of the transfer or secondary fuel pump, you might want to use a fuel caddy to drain the fuel, then pump it into the secondary tank to see if the pump sends it into the primary tank. This functional test might indicate if the pump and senders are working. 

Running Mode

On most modern systems, the strategy is to keep as much fuel as possible in the primary tank so the primary pump is submerged and cooled by the fuel. The system will pump fuel from the secondary to the primary as the fuel is burned. When the secondary side of the tank is empty, the fuel pump module draws fuel from only the primary side of the tank. On some vehicles, the system will balance the fuel between the tanks to optimize weight distribution until the fuel reaches a specific level.  

Typically, the operating criteria will be in the “operation and theory” part of the service information. Looking at this section is critical to diagnosing some systems.

Fuel-Level Calculations

The two fuel-level senders are critical to making saddle-style fuel tanks work. The fuel level sent to the driver is a reflection of the two sender inputs. The fuel pump module and the PCM also use the senders to determine if the system is operating properly. 

In some cases, a fault at the secondary side of the tank will cause the gauge to default to the primary side sending unit reading. This results in a maximum reading of half-tank. This reading will stay the same until the fuel level on the secondary side is empty and fuel on the primary side begins to drop. A fault with the primary-side sender will cause the gauge to read empty.

Most fuel pump modules are able to identify problems with the secondary or jet pump from the behavior of the fuel-level senders. The module sets these codes based on readings from the fuel tank sender units. The code will set when the PCM detects that the secondary side of the tank still has fuel stored and the primary-side fuel level begins to drop.

In some cases, the fuel level will still read quarter-tank or more when there is no fuel pressure. The primary pump will function and the circuit to the pump will be intact with no voltage drops. If the pump is replaced, the condition will return.

Ground connections and wiring harness issues are common problems for saddle-style tanks. If you have excessive voltage drops or inconsistent fuel-level readings, check the connections at the body and chassis grounds for excessive resistance. The top of the tank will often collect road salt and deicing brines that can cause shorts to ground.

You May Also Like

Ethanol & Fuel Systems

Here’s what you need to know about ethanol and E15 fuels.

This summer, in an effort to reduce prices at the pump, President Biden announced that the federal rule which bans the sale of E15 fuel during the summer months would be lifted. It’s no secret that prices at the gas pumps have risen sharply this year. There are many contributing factors to this, including market instability caused by the war in Ukraine, as well as significantly higher customer demand compared to 2020 when lockdowns were in place.

High-Pressure GDI Fuel Pumps

When solving a fuel pump issue, the scan tool is your best friend.

Fuel Tank Contamination

A number of things can cause a fuel filter to plug up.

Oxygen Sensors And Catalyst Efficiency

Newer air/fuel ratio or wide-band sensors can detect a wide range of fuel conditions.

Gasoline Direct Injection Is Better, But Not Perfect

GDI technology has improved but drivers could face problems if they don’t keep up with maintenance.

Other Posts

BMW Spark Plug Replacement

Here are a few things that you need to know before replacing spark plugs in a BMW.

Diagnosing Intercooler Boost Trouble Code P0299

The criteria for setting the code is very basic.

Understanding Engine Misfire Codes

When the fuel/air mixture ignites, many factors must be met to pass a misfire monitor.

What Caused The Turbo To Fail?

Up to 50% of turbocharger failures are due to oiling problems.