New Programmable Sensor Add-On Package For Snap-on TPMS3 – UnderhoodService

New Programmable Sensor Add-On Package For Snap-on TPMS3

The Snap-on TPMS3 Tire Sensor System Tool just got a whole lot better with the introduction of the new Snap-on Programmable Sensor Add-on Package (TPMS3PRG). With this new capability, service technicians can program replacement or duplicate aftermarket tire pressure monitoring sensors, saving time and reducing sensor inventory.

The Snap-on TPMS3 Tire Sensor System Tool just got a whole lot better with the introduction of the new Snap-on Programmable Sensor Add-on Package (TPMS3PRG). With this new capability, service technicians can program replacement or duplicate aftermarket tire pressure monitoring sensors, saving time and reducing sensor inventory.

“The Snap-on TPMS3PRG activation enhances the capabilities of our TPMS3 tool, allowing technicians the opportunity to replace a broken or nonfunctioning sensor by programming a duplicate sensor with an identical ID.  In addition to this, it can also be used to create a generic sensor ID as well,” said Mike DeKeuster, category manager for Snap-on. “With TPMS3PRG, users can program universal sensors to fit multiple vehicles, greatly reducing the variety and number of sensors that shops need to keep in inventory.” 

The new Snap-on TPMS3PRG is an optional activation that allows users to utilize their existing or new Snap-on TPMS3 tool to program aftermarket TPMS programmable sensors. The TPMS3PRG can replace a sensor with low battery life or one that is non-functioning, as well as create a duplicate set of sensors for customers that change from summer to winter sets of tires. The TPMS3PRG works with all the major aftermarket sensors including: EZ-sensor, Alligator sens.it, Dorman DiRECT-FIT, Standard Clone-able, NAPA Echlin Clone-able, Intermotor Clone-able and OEC ID Copy (Orange).

The Snap-on TPMS3PRG kit consists of a registration certificate containing a web TPM code which allows access to sensor programming functionality and a 2GB micro SD storage card. The kit requires TPMS3 software version CS2-02 or newer. TPMS3PRG is a one-time activation to program aftermarket TPM sensors and subsequent updates to TPMS3PRG are part of the standard TPMS3U annual update.

Customers can learn more about the new Snap-on Programmable Sensor Add-on Package for TPMS3 (TPMS3PRG) by contacting their participating Snap-on franchisee or representative, visiting www.snapon.com/shoptools or by calling toll free 877-SNAPON-4 (877-762-7664).

 

You May Also Like

Detecting Misfire And Knock Conditions

Knock sensors are mounted on the block near the base of the cylinder head.

The knock sensor is a piezoelectric accelerometer that acts as a microphone on the engine. It converts vibrations into alternating current (AC) signal. When the crystal inside the sensor is vibrated, it produces an AC voltage. The greater the vibration or shock, the higher the voltage and frequency.

Mercedes Ignition Coil Pack Diagnostics

Replacing a single coil might not be the best approach to curing an engine of a chronic misfire.

Chrysler’s Totally Integrated Power Module

The TIPM is on the CAN bus, any issues with the communication between the ECM, ABS and BCM can cause problems with the TIPM.

Mercedes EQS Service Opportunities

EQ is the EV brand for Mercedes. It is the equivalent of Audi’s Etron or VW’s iD brands.

ADAS Calibration Tips

Here are 10 tips to follow during ADAS Calibration.

Other Posts

A/C System Manifold Gauges

A basic gauge set will have three basic components.

Chassis Control Modules After Reconnecting Battery

To resolve the issue, fully disconnect the negative lead from the battery terminal.

HVAC Diagnostics

Knowing the cause of the complaint might require looking at several components.

Reflashing Power Supplies

A power supply to keep the system voltage consistent is a required piece of equipment to perform a reflash procedure.