What Are the Advantages of Twin-Tube Shocks? – UnderhoodService

What Are the Advantages of Twin-Tube Shocks?

Twin tube shocks and struts have been used as original equipment on most vehicles for many years. But in recent years, we’ve also seen more monotube shocks and struts being used as original equipment dampers on sports and performance vehicles. So what’s the difference and what are the advantages and disadvantages of each design?

This month, we’re going to look at twin-tube shocks and struts to better understand how these ride control products evolved and how they work. Next month, we’ll follow up with monotube shocks and struts.

A LONG HISTORY
As vehicles became capable of faster speeds, the first add-on “friction dampers” appeared. These primitive shock absorbers had two arms connected at a pivot point with metal and leather washers at the elbow. One arm was connected to the axle and the other arm to the frame. When the suspension moved up and down, the leather and metal washers at the elbow rubbed against each other to create friction and dampen the motion. An adjustment bolt at the elbow could be tightened or loosened to modify the amount of friction or dampening provided by the unit.

In 1906, a friction shock that used a special friction material (Ferodo) in the elbow joint was patented by E.V. Hartford, making Hartford shocks a popular design for more than 30 years. Later designs added a bowden cable so the shocks could be adjusted on the fly from the driver’s seat (making these the first “adjustable” shocks).

The first telescoping hydraulic shock was invented in 1901 by C. L. Horock, according to the Bosch Book of The Motor Car. This was the predecessor of the modern shock absorbed because it used a piston in a fluid-filled cylinder. The shock featured an adjustable bleed hole and valving between the ends of the cylinder to control fluid movement and dampening action. The piston also had a one-way valve that allowed the shock to compress with little resistance to absorb bumps, then to offer greater resistance on rebound to dampen the suspension. This was a major improvement over friction shocks because it allowed variable two-way dampening between compression and rebound.

The telescopic design was also compact and direct acting. There was no arm to deflect or bend or break, and the force generated by the motions of the suspension traveled directly down the center of the shock. It was also a simple design that was economical to manufacture.

During these early years of automotive history, “hybrid” shocks appeared that combined elements of the earlier friction shocks with hydraulic dampening. Most of these shocks had an arm that attached to the axle like a friction shock, but the pivot was connected to a pair of blocks or pistons in a housing that pumped hydraulic fluid back and forth to dampen the suspension. Some of these early shocks were “single-acting” designs that only worked on rebound, while others were “double-acting” shocks that dampened the suspension during jounce and rebound. Though these designs were used on many cars in the 1920s, they proved to be an evolutionary dead end.

As vehicle technology evolved and suspensions designs moved away from solid front axles to control arms and independent suspensions, the telescopic hydraulic shock become the predominant damper.

In 1932, the Hudson Motor Car Company was the first automaker to equip its cars with four direct-acting hydraulic shocks. Other automakers, such as Auburn, Reo, Chrysler, Packard and Terraplane, soon followed suit. In 1949, Ford changed to direct-acting hydraulic shocks, followed by Chevrolet in 1950.

DIRECT-ACTING SHOCKS
Direct-acting hydraulic shocks became the norm because as vehicles became heavier, spring rates got softer. Motorists wanted a smoother ride with less bounce, so direct-acting shocks that provided variable dampening action both ways provided the answer that the public wanted.

In a twin-tube direct-acting shock, there is an inner tube for the piston cylinder, and an outer tube that serves as a fluid reservoir. Valves in the piston and in the bottom of the shock control fluid flow in both directions and determine the dampening characteristics of the shock.

During the compression stroke when the piston moves down, some fluid flows through the piston valve from the lower chamber below the piston to the upper chamber above the piston. At the same time, some fluid in the lower chamber is also displaced through the valve in the bottom of the shock into the outer reservoir. If there were no valving in the piston or the bottom of the shock, the piston would hydrolock as if it had hit a solid wall because fluid is incompressible. So the piston has to have orifices and/or some type of valving that allows the piston to move through the liquid. The valving at the bottom acts sort of like a safety valve and allows excess pressure in the lower chamber to vent into the reservoir when the vehicle hits a hard bump. The valve is usually velocity-sensing, which means it doesn’t open unless there is a sudden and sharp increase in pressure.

Piston size is also a factor. The larger the bore size, the greater the volume of fluid that’s displaced with every stroke of the piston inside the shock — which provides greater dampening ability. Thus, heavy-duty shocks typically have larger bore diameters than standard shocks.

During the extension cycle when the suspension undergoes rebound and pulls the shock out, the upward movement of the piston generates pressure in the upper chamber as it pushes through the fluid. The piston also sucks fluid back into the lower chamber from the reservoir when the valving in the bottom of the shock opens.

By using “staged” valving, the rate at which fluid moves between the upper and lower chambers, and the lower chamber and the outer reservoir can be carefully controlled to modify the dampening characteristics of the shock. At low shock velocity, the valving can be set to allow easy movement between the chambers for a soft, boulevard-like ride. As shock velocity increases, the valving can change to create more resistance and “stiffen” the shock for better ride control.

The valving can be designed to be equal in both directions (50/50 shocks), or much higher in one direction and lighter in the other (as in the 90/10 front shocks used in drag racing that extend easily to improve weight transfer to the rear wheels, but are slow to compress).

Shocks can also be calibrated so that they vent pressure and compress easily when hitting a bump, or vise versa. The valving can also be made variable with a mechanical dial (adjustable shocks) or a solenoid that changes the valving (electronic shocks).

Shock valving can also be modified by machining several small slits or grooves into the wall of the piston chamber. These grooves are positioned in the middle area of the shock where the piston spends most of its time. By allowing more fluid to bypass the piston, the grooves provide a smoother ride in the “comfort” zone. But when the piston travels up or down beyond this range, it encounters more resistance and provides stiffer control.

Something else to keep in mind is that a shock absorber converts the energy of motion into heat. The faster a shock is pumped up and down, the more resistance it creates and the more heat it generates. The heat is dissipated into the fluid, the shock body and the surrounding air. On a rough road, a shock can get pretty hot. If the shock does not get adequate cooling, the oil can thin out and cause the shock to fade.

CAVITATION & FOAMING
If you’ve even seen a cutaway shock with a see-through glass or plastic piston chamber, you can see what happens to the fluid when the piston pumps up and down. At relatively slow speed, the fluid just moves back and forth (not very interesting). But when you pump the shock up and down rapidly, air bubbles form behind the piston. Engineers call this cavitation, and it causes aeration and fluid foaming. The hydraulic fluid turns into a frothy mixture of air and oil that resembles a good head on a fresh glass of beer. Fluid aeration and foaming is not a good thing inside a shock absorber because air is compressible and is much thinner than the liquid it displaces. Consequently, the shock starts to “fade” and provides much less resistance and ride control than it did before the fluid started to foam. On a rough road, this can cause a lot of tire bounce, loss of traction and even loss of handling control.

GAS-CHARGING
In 1956, a Frenchman named De Carbon found a solution for the foaming problem. He discovered that pressurizing the fluid with nitrogen, Freon or air helped reduce foaming. He took his idea to the German shock manufacturer Bilstein, and they patented a design for a single tube (monotube) shock with a high pressure (360 psi) gas charge in the bottom of the shock. A floating piston separated the gas charge from the hydraulic fluid.

The original patent expired in 1971, and similar designs were soon developed by other companies. Gas-pressurized monotube as well as twin-tube shocks soon became popular in the aftermarket for racing and performance applications.

It wasn’t long before the automakers picked up on the new technology and began equipping their vehicles with gas shocks and struts as original equipment. In 1982, the first original equipment gas-charged twin-tube shocks were used on the Lincoln Continental. The first adjustable gas-pressurized shocks were introduced 1979.

TWIN-TUBE ADVANTAGE
One of the advantages of a twin-tube gas pressurized shock is that less gas pressure can be used to prevent the fluid from foaming. Some twin-tube shocks contain as little as 35 psi, while others may contain as much as 100 to 150 psi. This eliminates the need to have a highly polished piston bore with a floating piston (which lowers manufacturing costs), and it allows a softer ride for everyday driving.

The gas charge in the top of the outer fluid reservoir works like a pressure cooker to prevent foaming. This significantly improves ride control performance by reducing fade, noise and roughness. It also allows more latitude in shock valving for a wider range of control compared to a conventional shock or strut.

The twin-tube shock is also less expensive to manufacture than a monotube shock because it does not require a high polished piston chamber, or a floating piston to separate the gas charge from the oil inside the shock.

You May Also Like

HVAC Sensors: More Than Just Temperature

When a driver sets a temperature in the control head of an HVAC system, what does it mean to the vehicle? Seventy-two degrees could mean many different settings depending on the outside temperature, humidity and even the position of the sun.

When a driver sets a temperature in the control head of an HVAC system, what does it mean to the vehicle? Seventy-two degrees could mean many different settings depending on the outside temperature, humidity and even the position of the sun.

When a passenger decides that 70 degrees is a better temperature for their zone, things get even more complicated. Automatic Temperature Control (ATC) systems require a complex array of internal and external sensors that include ambient air temperature sensors, interior temperature sensors, outlet duct and evaporator temperature sensors, pressure sensors, humidity sensors, blend door position sensors and sunload sensors.

Nearly 5,000 To Participate In Auto Value, Bumper To Bumper ‘Festive Walk’ To AAPEX 2018

On Thursday, Nov. 1, nearly 5,000 Auto Value and Bumper to Bumper automotive professionals wearing matching yellow shirts will begin their “festive walk” from the Mirage hotel to AAPEX 2018 at the Sands Expo, temporarily shutting down the busy Las Vegas Boulevard along the way.

Drive Belt Checklist: What Are You Missing?

You might have only one chance to sell a customer a new serpentine belt. With belts lasting roughly 90,000 miles, proper inspection at the time of failure is critical not only for selling the belt, but also for ensuring add-on sales and better customer satisfaction.

VIDEO: Using Airflow To Sell Cabin Air Filters

Andrew Markel introduces an inexpensive tool that can assist in selling cabin air filter replacements. Sponsored by Auto Value and Bumper to Bumper.

airflow-selling-cabin-air-filter-video-featured
Air Conditioning Odor Causes

Air conditioning odors typically result from the uncontrolled growth of bacteria and other microorganisms in the evaporator. Research by independent laboratories has found fungi such as Aspergillus, Cladesporium, Penicillium and others growing on cooling coils and other A/C system areas.

ac air conditioning smells featured

Other Posts

Climate Control Modules

HVAC control modules may fail when the contacts and switches become inoperable. Sponsored by The Group Training Academy.

Paired Ride Control (VIDEO)

It’s always best to replace ride control parts in pairs. Sponsored by GSP North America.

Dorman Launches 300+ New Products In November

Among the new products is an OE FIX climate control module designed to fit 1.7M Chevrolet Express & GMC Savana vehicles.

Curing Springtime Air Conditioning Smells

Air conditioning scents can come from a host of things.