VIDEO: Belt Inspection

VIDEO: Belt Inspection

Noise is the first sign that more components than just the belt need attention. This video is sponsored by Continental.

When it comes to belt inspection, there are three questions you need to ask.

Is there noise?

What do the surfaces of the belt and pulleys look like?

Is the wear across the belt or in a specific area?

If you can confidently answer these questions, you can not only make the right call on the belt, but the entire belt drive system.

Noise is the first sign that more components than just the belt need attention. Listen to the belt before proceeding with the rest of the inspection. The first clue is a belt squeal heard during engine start-up. The second clue might be a belt squeal heard during parking maneuvers or during an alternator load test.

Appearance of the belt’s grooves and pulleys matter. Late-model belts should not crack or show signs of abuse in normal operation. The belt should wear uniformly. The OE-recommended service interval is based on this wear and not on signs of cracking. Once enough material is worn away from the grooves in the belt, the grooves on the pulley bottom out, and the belt is not able to grip the alternator, power steering pump or A/C compressor. This is why following replacement intervals and measuring rib depth, using a belt wear gauge, is critical to keeping the belt and system healthy. Abnormal wear like cracking, pilling and glazing on the grooved side of the belt is a sign there might not be a problem with the belt, but maybe with the idler pulleys, tensioner or and other connected devices such as an OAD. So, replacing just the belt does not solve the underlying problem.

Cracking and missing chunks on modern belts are usually signs of high under the hood temperatures. Slipping on the pulleys creates friction and heat. If oil or coolant comes in contact with the belt, the slipping can increase and cause even higher temperatures.

Look at the entire surface of the belt. If the abnormal wear is in only one area, it is a sign the belt was damaged during installation or an incident occurred where an object came between the belt and pulley.

If the pulleys are misaligned, wear will occur on one edge of the belt. The edge is one of the most sensitive areas on the belt because the structural fibers are exposed. Edge wear is typically caused by misalignment of the pulleys.

By listening for noise and inspecting the belt, you not only spot a worn belt, but other conditions that can cause the new belt to suffer the same fate!

This video is sponsored by Continental.

You May Also Like

Rust and Corrosion Preventive Oil (VIDEO)

Your tools and equipment need to be protected from rust. This video is sponsored by Lubegard.

Welcome to Rustgard, rust and corrosion preventive oil by Lubegard, product overview.

Rust and corrosion can destroy tools and equipment, and it only takes a little moisture to trigger rust. Whether in your garage, shed, or shop, temperature and humidity levels are constantly fluctuating and your tools and equipment need to be protected.

Auto Pros Team Visits Hybrid Shop of The Carolinas

Auto Pros on the Road puts the Babcox team into shops across the USA. This episode is sponsored by Autolite.

2007-2021 Toyota Tundra Strut Replacement (VIDEO)

Follow along the step by step installation process for struts on 2007-2021 Toyota Tundra’s. This video is sponsored by PRT.

AMN Drivetime: MEMA Leaders Chat About The Future

MEMA leaders sat down with Bill Babcox to share a few updates on the realignment of the association announced in November.

Ford F-250 Shock Replacement (VIDEO)

Follow along the step by step installation process of shocks on a Ford F-250. This video is sponsored by PRT.

Other Posts

How Speed, Load and Slip Affect Voltages

Modern, computer-controlled charging systems found on today’s vehicles need proper test procedures – no guesswork allowed.

Engineering Better Belt Systems

You might not be able to see it, but an accessory drive belt is always both speeding up and slowing down.

Creating Parts: The Manufacturing Process (Video)

Creating parts takes many steps worth of work. Sponsored by AP Emissions.

Direct Fit Catalytic Converters Features and Benefits

Four qualities stand out the most when looking at these catalytic converters. Sponsored by AP Emissions.