Top 5 Spark Plug Tips

Top 5 Spark Plug Tips

Here are five little-known tips about spark plug replacement that you probably didn't learn in school.


Here are 5 little-known tips about spark plug replacement that you probably didn’t learn in school.


1. Getting Plugs Out: Chemical Tools

If a spark plug is difficult to remove, some fluids can help break up corrosion and carbon between the threads on the plug and head. You can pour a liquid penetrant into the wells and let it sit for an hour or longer. Some technicians have had luck with an in-tank fuel injector cleaner to help break up the carbon that forms between the plug and the head, like that which occurs on Ford modular V8s. The key with this method is time; the longer the fluid is in the well, the better the penetration.

If you have a spark plug that feels notchy, the fluid method can prevent damage to the threads. Just crack the plugs a quarter turn and pour in a penetrant or fuel injector cleaner. If you used a lot of fluid, you might need to change the oil after the plugs are replaced.

2. Spark Plug Hole Hygiene
The spark plug well or tube should be free of oil, water and debris. Removal of the spark plug can be difficult, if anything exists in the tube or well. Over time, debris and fluid can help to create a path to ground because the secondary ignition creates static electricity that attracts small particles to the insulator. If you see oil or other debris in the spark plug tube or well, replacing the valve cover gasket or the boot on the coil can prevent a misfire in the future.

3. Engine Temperature Removal
A controversial topic among technicians and engineers is whether the engine should be hot or cold when replacing the spark plugs. The OEMs and spark plug manufacturers always recommend removing and installing the plugs when the engine is cold. The reasoning is that this is when the spark plug and head have the least amount of thermal expansion and the chances of damage to the threads. This is critical when you consider that the head might be aluminum and the plug is steel.

Believers in the “removing when hot method” can’t really explain why it works. Some say it loosens up the galling and corrosion between the threads of the plug and the head. Some of them even insist that the use of an impact can help break the plug loose. If it works for you, go with the hot method. Just make sure you have all of the tools to repair the threads and install inserts.

4. Coil Bolts
Always apply the specified torque to the specified mounting thru-bolt for the coil. Loose thru-bolts could lead to failures under vibration. Over tightened thru-bolts could lead to a cracked coil mounting ear and/or premature thru-bolt failure. Not getting it right can lead to a diagnostic nightmare.


5. Under or Over Torqued

Most articles will tell you to use a torque wrench, but they never explain why. The real reason involves heat transfer. An under-torqued spark plug will not make full contact with the cylinder head. This reduces a plug’s ability to transfer heat and will result in elevated combustion chamber temperatures. This can cause pre-ignition and detonation and lead to engine damage. An over-torqued spark plug can cause stress to the metal shell, leading to thread damage or breakage. Also, excess tightening can compromise a plug’s internal gas seal or even cause a hairline fracture to the insulator.

You May Also Like

Acura Turbo Engine Service

It is important to check the operation of the solenoids that control vacuum to the actuators.

The 2007-2012 Acura RDX was Honda’s first production vehicle in North America with a turbocharger. The company took the proven K-series engine and lowered the compression ratio from 10:1 to 8:1, and added a turbocharger with the associated plumbing. But, it is a lot more complicated when it comes to managing the boost.

Subaru EJ25 Head Gasket Problems

Most of the EJ head gasket failures occur around the 100,000-mile mark and start as a slow oil or coolant leak.

Honda Electronic Throttle Body Service Tips

Using care and following OEM procedures will help you to avoid unnecessary parts replacement and comebacks.

New Oil Specifications

Many 0W16 oils have a new donut certification mark on the bottle called API SN-PLUS and SN-PLUS Resource Conserving.

Solving Intermittent Overheating

New cooling systems anticipate and influence changes in coolant temperature.

Other Posts

Deciphering Engine Misfire Codes

When the fuel/air mixture ignites, many factors must be met to pass a misfire monitor.

Cabin Air Filter Replacement

There are three major reasons to replace a cabin air filter in the winter.

Today’s Fuel Pressure Diagnostics

Direct injection pressure is measured with sensors, and you’ll need a scan tool to measure the signals

Diesel Air Filter Replacement

Here are some diesel air filter replacement tips in order to keep these vehicles running as intended.