Tech Tip: Squeak-Like Sound from Front Bumper Crossmember on Jeep Liberty and Cherokee Vehicles – UnderhoodService

Tech Tip: Squeak-Like Sound from Front Bumper Crossmember on Jeep Liberty and Cherokee Vehicles

A customer may experience a squeak-like sound when driving slowly over driveway entrances, road bumps or when performing parking lot maneuvers. The squeak-like sound may occur when the vehicle body/frame is flexed (twists). This condition may occur when the front edge flange of either frame rail rubs against the backside of the front bumper crossmember.

Vehicles: 2002 Jeep Liberty and Cherokee models.

Symptom/Condition:
A customer may experience a squeak-like sound when driving slowly over driveway entrances, road bumps or when performing parking lot maneuvers. The squeak-like sound may occur when the vehicle body/frame is flexed (twists). This condition may occur when the front edge flange of either frame rail rubs against the backside of the front bumper crossmember.

Diagnosis:
With the vehicle stopped and in park, slowly rock the vehicle from side-to-side. Applying force to the top edge of the driver or front passenger side door opening may be of assistance. If present, the squeak-like sound will come from behind the front bumper fascia and in the immediate area below either front headlamp.

Another diagnostic method is to set the parking brake, start the vehicle engine, and while in park, slowly turn the vehicle front wheels from side-to-side (to flex the body) while someone listens at the front of the vehicle.

If the above condition is present, perform the Repair Procedure to both the left and right side of the front bumper crossmember.

Repair Procedure:
1. Remove the vehicle front grill and fascia. For additional disassembly and assembly instructions, refer to the Frame & Bumper section of the appropriate 2002 service manual.

2. Remove the screw used to secure the right side frame rail end cap to the front bumper crossmember. The frame rail cap covers the rectangular access hole in the crossmember. Remove the end cap.

1 – Right Side Frame Rail
2 – Weld Lines – already present
3 – Front Bumper Crossmember
4 – Mark line as specified, clamp panels, center punch, drill 3/16 in. holes, add rivets
5 – Draw vertical line 9 mm from inboard edge of rectangular access hole.
5 – Five (5) spot welds – already present.

3. Draw a verticle line from the top to bottom across the width of the front crossmember. The vertical line should be positioned so that it is 9 mm to the right, and parallel to the inboard vertical edge of the right access hole (in the crossmember). See illustration in Figure 1.

4. Mark the vertical line in three places as illustrated. Each top and bottom mark is to be 20 mm (.750 in.) from the top and bottom edge of the crossmemver respectively. The middle mark is to be centered at 50 mm (2.0 in.) from the top and bottom edge of the crossmember.

5. Center punch all three marks to prevent drill bit drift and improperly positioned holes.

6. Position locking pliers through the rectangular hole in the crossmember. Tightly clamp the crossmember panel to the frame rail edge flange. Position the locking pliers so that they will not interfere with the drilling of the three holes or with the heads of the rivets when they are installed.

7. Using a 3/16 size drill bit, drill a hole at each of the three marks made on the vertical line. Drill all the way through both metal panels (the crossmember and frame rail edge flange).

8. Make sure the area around the three drilled holes is free of metal burrs. Install a suitable corrosion-resistant material (e.g. paint primer) to the drilled holes.

9. With the two panels securely held together by the locking pliers, install a rivet (p/n 34201208) in each drilled hole.

10. Remove the locking pliers.

11. Move to the rectangular access hole located at the left side (driver side) of the front bumper crossmember.

12. Perform steps 2 through 10 in a similar manner so that the installed rivets are positioned along the inboard edge of the driver-side rectangular access hole. The left side repair should mirror the repairs made to the right side.

13. Verify that the squeak-like sound condition has been corrected.

14. Install both end caps and screws.

15. Install the front fascia and grill.

For additional information, visit www.mitchell1.com.

Technical service bulletin courtesy of Mitchell 1.

You May Also Like

Check The TSBs!

With the complexity of today’s modern vehicles, as technicians, we are going to have to stay on top of our game.

Over the last 28 years of being a technician, I have developed the habit of checking for and reading technical service bulletins at the forefront of the diagnostic process, especially when an unfamiliar vehicle exhibiting blatant or straightforward concerns comes into the shop. I have found many valuable nuggets of information while reading over these bulletins, from wiring concerns and connector issues, to transfer noises, water leaks, and engine and transmission performance concerns. The knowledge gained in reading through these bulletins has not only helped me with the vehicles I’m working on, but also increased my perspective and ability to connect the dots on other vehicles that don’t pertain to a current bulletin.

HVAC Heat Pumps

In theory, heat pumps can be three to four times more energy-efficient than conventional electric heaters.

AMN Drivetime: Cal Ganda’s Continental Journey

Ganda embodies servitude leadership, prioritizing team success and customer-centricity.

Auxiliary Water Pump Diagnostics

A car or truck comes into your shop with a complaint of poor heater performance- the issue may be the auxiliary water pump.

Misfire Codes P0300, P0301-P0312 and P0313+P0314

The only way to clear the code is to use a crankshaft position relearn with a scan tool.

Other Posts

Eaton to Supply ELocker Differential System to EV Manufacturer

The system leverages an electric motor to power the rear wheels and an electric motor or an optional ICE driving the front wheels.

Replacing Your Power Steering Reservoir

Discover why simply flushing out contaminants from power steering reservoirs may not be sufficient to prevent potential failures.

What Caused The Turbo To Fail?

Up to 50% of turbocharger failures are due to oiling problems.

Eli Opens Reservations for its Micro-EV in the US

The new Eli ZERO represents a new category of high-tech, efficient and sustainable micro-EVs, according to Eli Electric Vehicles.