Tech Tip: Diagnosing a Lit Diamante Traction Control Lamp – UnderhoodService

Tech Tip: Diagnosing a Lit Diamante Traction Control Lamp

Darrel's wife has a 2002 Mitsubishi Diamante that she uses for shuttling around her real estate clients. Recently, the Diamante's TCL (Traction Control Lamp) came on. Concerned for his wife's safety, Darrel brought the car by for an inspection. We retrieved a code 72, but could not come up with a cause for the code. I talked to a friend who works for a Mitsubishi dealer and he turned me on to the solution.

By Eric Seifert
ALLDATA Automotive Technical Editor

Darrel’s wife has a 2002 Mitsubishi Diamante that she uses for shuttling around her real estate clients. Recently, the Diamante’s TCL (Traction Control Lamp) came on. Concerned for his wife’s safety, Darrel brought the car by for an inspection. We retrieved a code 72, but could not come up with a cause for the code. I talked to a friend who works for a Mitsubishi dealer and he turned me on to the solution.

Traction Control Diagnostic Trouble Code 72 or 73, “Vacuum Ventilation Control Solenoid Circuit System” may set, and the TCL light may come on, due to excessive ignition signal interference affecting the voltage in the TCL solenoid valve harness. This may also cause MFI DTC P1101 or P1102 to set in the PCM. To eliminate this condition, install a noise filter in the wiring harness at the distributor connector as described in the repair procedure.

The repair will require one Mitsubishi noise filter P/N MM902517.

Applicable Vehicles:
2001-2002 Diamante models equipped with TCL.

Repair Procedure:
1. Remove the plastic engine cover.

2. Disconnect the 7-pin connector from the distributor. See Figure 1.

3. Use a sharp blade to open the plastic harness covering behind the main loom to expose the wires.

4. At pin 2, cut the white wire 2” from the connector. See Figure 2.

5. Install a noise filter as shown in Figure 3. Be sure that the wires are properly positioned before soldering, and that a clean, strong joint is formed.

a. Solder the black wire to the connector side of the harness.
b. Solder the white/red wire to the harness lead.
c. Install heat shrink tubing over the soldered areas for insulation.

6. Reinstall the plastic harness covering and tape securely for a watertight seal.

7. Position the noise filter between the vacuum control valve bracket and the bolt as shown in Figure 4.

8. Reconnect the distributor connector.

9. Reinstall the plastic engine cover.

Eric Seifert is an ASE certified Master Technician and Engine Machinist, with 20 years of independent shop and parts store experience.

For additional information, visit www.alldata.com.

You May Also Like

FLO, GM Activate Plug and Charge for GM EV Drivers in Canada

FLO’s technology confirms identification, authorizes the charging session and activates billing without any additional action from the driver.

FLO and General Motors activated the Plug and Charge capability at all DC fast chargers on the FLO network across Canada. All GM EV drivers are provided with access to GM’s Plug and Charge, which is enabled by FLO’s autocharge software. The feature allows GM EV drivers to begin a fast-charging session by plugging in their vehicle at one of FLO’s fast charging stations across Canada, the company said.

Schaeffler and Sustainability with Jerry Conroy

Conroy shares insights into his career trajectory, the evolving landscape of the company’s aftermarket operations, and its commitment to innovation and sustainability.

Flushing the Brake Fluid is Critical on Every Brake Repair

Making sure the brake fluid is the correct quality is critical. Sponsored by Auto Value and Bumper to Bumper.

Selecting the Right Oil for your Customers Engine

Learn how to educate customers on the importance of OEM specifications and premium lubrication for their vehicles’ maintenance needs.

At the Intersection of Tradition and Innovation with Grace Hovis

Grace Hovis’s journey in Hovis Auto & Truck Supply blends tradition with digital innovation in the automotive aftermarket industry.

Other Posts

Inspection Tips For Chain-Driven Water Pumps

If one water pump fails sooner and is replaced without an investigation, the new pump is likely doomed.

Water pump feature
Power Window Regulator and Motor Service

Power windows are great as long as they roll up and down when commanded to do so.

Philips Announces GoPure GP5212 Automotive Air Purifier

It uses a 3-layer filter to deliver cleaner, healthier, fresher air on the go, Lumileds said.

Snap-on Announces Latest Software Release

The latest software includes new coverage and guided component tests and features.