Tech Tip: Creak-Type Noise Heard when Brakes are Applied – UnderhoodService

Tech Tip: Creak-Type Noise Heard when Brakes are Applied

Some customers may comment on a creak-type noise occurring when applying the brakes. It is usually heard only during slow speed brake maneuvers. This condition may be caused by a caliper piston to seal interface issue during brake apply. If the caliper is removed and the piston is pushed back, the noise may be eliminated. This is usually only a temporary fix.

Vehicles:
• Chevrolet: 1999-2003 Malibu; 2004 Malibu Classic
• Oldsmobile: 1999-2004 Alero
• Pontiac: 1999-2004 Grand Am

Condition:
Some customers may comment on a creak-type noise occurring when applying the brakes. It is usually heard only during slow speed brake maneuvers. If this condition exists, it should be able to be duplicated when the vehicle is not moving by depressing the brake and listening for the noise from the wheel-well/caliper area.

Cause:
This condition may be caused by a caliper piston to seal interface issue during brake apply. If the caliper is removed and the piston is pushed back, the noise may be eliminated. This is usually only a temporary fix.

Correction:
Note: Do not replace caliper.

To repair this condition, lubricate the entire circumference of the seal at the caliper piston interface using Kluber Fluid and the following procedure:

1. Remove the wheel and install two lug nuts. This will hold the rotor to the bearing surface so debris does not fall between the surfaces and cause lateral runout (LRO).

2. Remove the bottom bolt from the caliper assembly without disturbing the hydraulic system.

3. Swing the caliper assembly up so the caliper assembly is facing upward.

4. Thoroughly clean the piston boot with GM-approved Brake Clean. Pay particular attention to the area where the boot interfaces with the piston.

5. Using compressed air, dry the piston/boot area.

6. Remove the cap from the tip of the bottle and carefully insert the tip, p/n 89022161, between the boot and piston, inward of the piston boot groove.

7. From the top side of the piston (see Figure 1), inject the lubricant. With the caliper in the tilted position, the lubricant will flow down and work its way around the entire circumference of the seal. Let the caliper body assembly remain in this position for a minimum of two minutes to allow for the fluid to completely work its way around the seal.

8. Push the piston into the seal to ensure the lubricant is on both the piston and seal surface.

9. Wipe away any excessive fluid.

10. Reassemble the caliper to the vehicles. Tighten the caliper bolts to 31 Nm (23 lb.ft.).

11. Repeat steps 1-9 on opposite side of the vehicle, if necessary.

12. Pump the brake pedal to push the caliper piston back into place.

13. Reinstall the wheel and test drive the vehicle to verify the repair.

Technical service bulletin courtesy of Mitchell 1.

For additional information, visit www.mitchell1.com.

You May Also Like

Do You Know The Cause Of A No-Spark Condition?

A no-spark condition could be the result of communication errors or missing data from a dead module.

Technicians, shop owners and service advisors are not Shakespeare. If something can be summed up in two words, we will do it. Unfortunately, this can lead to a loss of detail when it comes to an ignition complaint or symptom. 

Take the phrase, “no spark.” It typically means the engine is not starting because a spark can’t be “seen” or “felt” between the electrodes. But, “no spark” is not a diagnostic or repair path. 

Belt-In-Oil Timing Systems

Oil contamination of the belt drive has been a death sentence, due to the rubber and fiber construction of the belt.

Building The Perfect Future By Mentoring

Share your stories of how you have helped others reach their goals.

Solving Intermittent Overheating

New cooling systems anticipate and influence changes in coolant temperature.

Spark Plug Fouling

Understanding why spark plugs get dirty.

Other Posts

PCV System DTC

PCV systems are far more complex now, but they are also much better at controlling crankcase pressure.

What Caused The Turbo To fail?

Up to 50% of turbocharger failures are due to oiling problems.

Fuel Trims

To gain a better perspective on fuel trims, think about how “analog” vehicles dealt with changing fuel and air mixtures.

.01 Micron Superstar Filter

The .01 Micron SuperStar Filter includes a differential pressure gauge and comes with mounting brackets.