Tech Tip: Checking Compression Ring Gaps – UnderhoodService

Tech Tip: Checking Compression Ring Gaps

Ring gaps are often a confusing and misunderstood part of a rering job. There are minimum and maximum ring gap specifications that must be observed for the best performance of a new ring set.

Ring gaps are often a confusing and misunderstood part of a rering job. There are minimum and maximum ring gap specifications that must be observed for the best performance of a new ring set.

Minimum gap tolerances must be observed in order to prevent the ring ends from butting together as the ring expands when the engine approaches operating temperature. It is recommended that you use a minimum gap of .0035˝ per inch of cylinder diameter. 



Example: 4˝ (bore) x .0035 = .014 minimum gap.


figure 1 indicates the specifications for compression ring gap as outlined by the sae.
Maximum ring gap is an important part of ring performance in that too much gap results in lost compression, power loss and ultimately poor oil control. 



The chart in Figure 1 indicates the specifications for compression ring gap as outlined by the SAE (Society of Automotive Engineers) as standards for the automotive piston ring manufacturers.



An important fact to remember is that the manufacturers rigidly adhere to these tolerances and that the ring gaps are inspected in gauges accurate to .0001˝ at the cylinder diameter the ring is manufactured for. Any increase in the diameter of the cylinder is being used in, over the designated size, results in an increase of approximately .003˝ in ring gap for each .001˝ increase in cylinder diameter.



In order to check ring gap, the rings should be placed at the lowest possible part of the cylinder (below ring travel area) as this is the portion of the cylinder which is unworn and which the ring is sized for. Checking ring gap in the worn portion of the cylinder will show a gap increase in direct relation to the amount of cylinder wear present. The illustration in Figure 2 shows the effect of cylinder wear on ring gap.


Figure 2 shows effect of .012˝ cylinder taper on ring gap in 4-inch bore.
Figure 2 graphically illustrates the effect on ring gap that cylinder wear has. You will notice that the tapered cylinder has .012˝ wear at the top portion of ring travel which increases the ring gap .036˝. Therefore, it is entirely possible for the ring to have .061˝ end gap in that portion of the cylinder and be within recommended manufacturing tolerance.



For this reason, it is recommended that you use a maximum of .003˝ wear per inch of cylinder diameter, not to exceed .012˝ for successful reringing. If a cylinder is worn in excess of this it should be rebored and the proper oversize ring installed.

Checking ring gaps can give an approximation of cylinder wear as well as keep you from installing wrong sized rings for the application being rerung.

Tech Tip courtesy of Hastings Piston Rings.

You May Also Like

Tools To Service Serpentine Belts

Servicing the serpentine belt on some vehicles is a tough task.

Servicing the serpentine belt on some vehicles is a tough task. Without the right tools it is almost impossible. Here are six tools your shop needs to make your next belt replacement more productive.

Don’t Fight It
If you are still fighting belt tensioners with 3/8” breaker bar and wrenches, there are better solutions. There are serpentine belt kits that can help you get the right angle and attachment point on a tensioner to remove the old belt and install the new belt.

Battery Charging and Diagnostics

Here are six tips to use when diagnosing a vehicle with a dead battery. 

Why Do Timing Chains Stretch?

As the timing chain wears, it can change the timing of the camshaft and crankshaft.

Carbon Deposits and Direct Injection Engines

The primary cause of these problems is that fuel and added detergents are not hitting the back of the intake valves.

Acura Turbo Engine Service

It is important to check the operation of the solenoids that control vacuum to the actuators.

Other Posts

Subaru EJ25 Head Gasket Problems

Most of the EJ head gasket failures occur around the 100,000-mile mark and start as a slow oil or coolant leak.

Honda Electronic Throttle Body Service Tips

Using care and following OEM procedures will help you to avoid unnecessary parts replacement and comebacks.

New Oil Specifications

Many 0W16 oils have a new donut certification mark on the bottle called API SN-PLUS and SN-PLUS Resource Conserving.

Solving Intermittent Overheating

New cooling systems anticipate and influence changes in coolant temperature.