Tech Tip: Brake Burnishing Procedures for New Brake Pads or Shoes – UnderhoodService

Tech Tip: Brake Burnishing Procedures for New Brake Pads or Shoes

After every brake job the technician should first confirm that he has a good brake pedal by gently stroking the pedal to move the wheel cylinders and caliper pistons back out to the normal position. After confirming a good pedal, the follow burnish procedure should be used during the test drive ....

At Bendix, we highly recommend that new pads and shoes be broken in properly.

After every brake job the technician should first confirm that he has a good brake pedal by gently stroking the pedal to move the wheel cylinders and caliper pistons back out to the normal position. After confirming a good pedal, the follow burnish procedure should be used during the test drive:

30/30/30 Burnish Procedure

• Perform 30 stops from 30 miles per hour with a 30-second cooling interval between stops. These stops will be performed at a decelerating rate of 12 feet per second or less. This means that it should be a gentle easy stop.

• The 30/30/30 Burnish Procedure beds the pads and shoes into the rotor and drums. It also deposits the necessary friction transfer to the rotors and drums for optimum brake performance.

• Following this procedure also assures that your customer will have excellent brake performance from the first time he or she drives the car after brake service has been performed. You should not depend on your customer to break in the brake job. The only way to assure that it is done correctly is to incorporate it into your brake job test drive.

Remember, proper burnishing assures a long lasting, high performing, noise free brake job!

Courtesy of Bendix by Honeywell.

For more information and brake tips, visit www.bendixbrakes.com.

You May Also Like

Transmission Line Replacement

Transmission fluid likes to be at a constant temperature. If it is too hot or too cold for too long, the performance can fluctuate and potentially cause damage to the transmission.

Transmission fluid likes to be at a constant temperature. If it is too hot or too cold for too long, the performance can fluctuate and potentially cause damage to the transmission.
If the fluid is at a constant temperature, it behaves in a consistent manner in terms of its friction and lubrication properties. What can help control the temperature is the transmission cooling circuit.
The path of the fluid in the transmission lines is not as much about the destination as the journey. The size and length of the transmission lines, along with the size of the cooler, controls the temperature of the fluid. Also, the size of the engine and weight of the vehicle can determine the design of the transmission fluid cooling circuit.
Another thing to consider is how a modified transmission with a larger transmission cooling circuit might do more damage than good. On modern vehicles, the cooling circuit is designed to manage the fluid temperatures during startup. If the fluid can’t warm up quickly due to the increased volume, damage to the transmission friction surfaces can occur. The same goes for a bypassed cooling circuit. Why? Because fluid that is too hot can damage friction surfaces.

VIDEO: AAPEX 2016 Insights

Andrew Markel discusses his take on conversations he had with economists at AAPEX 2016, including the future of purchasing parts.

BMW Tech Tip: Oil Separator Replacement

A clogged oil separator valve is a common problem on many BMW DOHC inline sixes. The high failure rate is caused by sludge build-up that can result in oil burning, rough idle and engine fault codes. Although the solution is pretty simple, replacing the valve is labor intensive and can take anywhere from six to nine hours.

New IDUSA Premium Guard Website Offers Easy Access To Wide Range Of Oil, Air, Cabin, Fuel And Transmission Filters

The new website’s bi-lingual, responsive design features look-up powered by ShowMeTheParts.

VIDEO: How To Deal With Air Conditioning Smells

Andrew Markel discusses what to do to get rid of A/C smells after customers have tried to do it themselves.

Other Posts

Spray Now or Pay Later

Time measures the profitability of both a shop and technician, and experience is the best tool for profitability and productivity. The more you work on cars and trucks for a living, the more realize that some things might cost you pennies, but not using it can cost you dollars—this is certainly the case with WD-40

VIDEO: Brake Pads Deconstructed

Brake pads are thoroughly developed to produce the best result. This video is sponsored by ZF Aftermarket.

ChrisFix Talks FMSI And New Z Numbers

ChrisFix, the world’s largest automotive DIY YouTuber with more than 7 million global subscribers, enjoys helping car owners with the nuts and bolts of automotive ownership and repair.  In his latest video, ChrisFix offers some good news from the Friction Materials Standards Institute (FMSI), which maintains the standardized part numbering system for aftermarket brake pads.

Oil Bath Air Filters

Long before people started using cotton gauze air filters soaked in oil, the oil bath air filter was the dominant filter on the market. The filter removes debris in the air by running it over oil and a mesh element. These filters worked great when most roads were dirt, but they could be messy to clean.