Summer Time Top-Off Troubles

Summer Time Top-Off Troubles

The next time you get a vehicle in for minor maintenance or the driver wants an inspection because they are taking a summer trip, take a look to see if they are topping off the engine oil or coolant. You might see dribbles of oil around the oil fill or coolant pooling at the top of the reservoir or radiator. In some cases they might stash bottles of oil under the hood or coolant jugs in the trunk. The point is that oil and coolant leaks should not be ignored. Topping off the levels is often more costly in the long run than repairing the leaking gasket or component. Advising a customer about the potential damage that can occur if they decline a leak repair is not a scare tactic, it is important that they know the real price of their decision.

Oil leaks can leave greasy, ugly stains on your driveway, but the real danger is potential engine damage or failure if your engine runs low on oil.
Oil leaking at the back of the engine may also cause the clutch to slip if the vehicle has a manual transmission. Oil can also produce blue smoke and unpleasant odors if it drips onto a hot exhaust manifold or exhaust pipe.

After six or seven years of service, the engine may start to leak oil. The older the engine, the more likely it is to leak oil due to aging gaskets and seals. As an engine ages, heat can cause gaskets to harden and shrink; molded rubber gaskets can lose their elasticity. Engine oil leaks occur most often at the valve cover and oil pan gaskets, timing chain cover and front and rear crankshaft seals.

Oil leaks can also occur if the crankcase is overfilled, or the positive crankcase ventilation (PCV) system is clogged, allowing pressure to build up inside the engine.

When oil leaks out of an engine, it attracts dirt. So, look for greasy stains around or below gasket seams and seals. Sometimes you can see oil dripping out while the engine is idling, but more often than not, the oil just slowly seeps out and causes grease buildup in the vicinity of the leak. When in doubt, steam clean the engine bay and check for leaks a day or two later.

Crankcase oil additives can sometimes help slow a leak by causing aged gaskets and seals to swell, but no additive will stop a major leak or repair a broken gasket or worn seal. Sooner or later you will have to replace the leaky gasket or seal.

When replacing a gasket, the first and most important job is to make sure the sealing surfaces are clean and flat. Be careful cleaning aluminum. The soft surface can be damaged by aggressive scraping with metal scrapers. Never use abrasive discs to remove the old material. Even the use of rough sand paper can prevent a gasket from sealing. Don’t forget to do a “post mortem” on the gasket being replaced as the old gasket may provide clues to why it failed.

Different gaskets have different application recommendations and requirements. Most gaskets and sets will have instructions included. Never go outside of the recommendations if possible because you may be doing more harm than good on a modern engine.

Do not overtighten pan cover bolts as this may crush and damage the new gasket. Some gaskets have built-in steel grommets that limit how far the gasket is compressed when the bolts are tightened down. Use an accurate torque wrench and follow the vehicle manufacturer’s torque recommendations.

Valve Cover Gaskets

When sealing up an oil leak, use a sealant that is a low volatile silicone approved for use with oxygen sensors. Some silicones contain chemicals that can be drawn through the engine’s PCV system and contaminate the oxygen sensor. Keep in mind that RTV is not used in most molded rubber applications; when RTV is required, instruction sheets will guide you through the process.

Valve cover gaskets need to withstand high operating temperatures, as well as freezing cold at startup, and still maintain a tight oil seal. Nearby exhaust manifolds, exhaust crossover in the cylinder heads, and EGR systems can all lead to extreme heat, which can take its toll on valve cover gaskets. In addition, they are generally the most visible and accessible gaskets on the engine, and as a result, conventional materials can often be overtorqued.

Modern gasket designs incorporate compression limiters (load stops) to prevent overtorquing. Choosing the right gasket is essential, so it makes sense to rely on the same parts that manufacturers the world over select—Victor Reinz valve cover gaskets.

Any comeback is bad but having to remove an inferior oil pan gasket will really ruin your day. Victor Reinz oil pan gaskets are built to meet or exceed the standards of original equipment manufacturers around the world and deliver the seal that prevents drops on the driveway.

Over the years, oil pans have evolved from simple stamped steel pans into sophisticated engine components that play a major role in controlling the engine’s NVH (Noise, Vibration, and Harshness). In late model vehicles, the engine crankcase, oil pan and oil pan gasket are all designed to form a complete sealing and NVH system. Victor Reinz has the expertise required to ensure complete compatibility with late-model oil-pan technology.

Oil Pan

Molded rubber-on-carrier oil pan gaskets from Victor Reinz use high-temperature silicone rubber seals precision molded on composite nylon or metal carriers. These materials meet or exceed SAE standards. Some carriers are encased in molded rubber and others have edge-molded rubber sealing beads depending on the application.

All Victor Reinz molded rubber gaskets use polymers chosen to resist compression set. This happens when a gasket loses its ability to “recover” against sealing surfaces, which can allow leakage.

To replace a leaky seal on the front of the crankshaft, the crank pulley/harmonic balancer must be removed before the seal can be pried out, which requires a gear puller. Do not pound on the pulley/balancer because this may damage it. If the surface of the crankshaft is worn, a slip-on repair sleeve can be installed to restore the surface. A special seal is usually required with a repair sleeve.

Leaky rear main bearing seals are time consuming to replace. because they involve dropping the oil pan and unbolting the rear main crankshaft support cap inside the engine. On applications that have a one-piece rear main oil seal instead of a split seal, the flywheel has to come off, which means pulling the transmission.

Victor Reinz rear main seal sets contain both the rear main seal and retainer gasket when required. Victor Reinz valve stem seals are engineered for precise control of valve stem lubrication – requiring very sophisticated designs that have to accommodate the full range of engine RPMs and operating temperatures.

You might know it by a brand name for non-stick products, but in the world of gaskets we simply refer to polytetrafluoroethylene as PTFE, and it’s setting a new standard in sealing for today’s engines. Keep in mind that unlike conventional seals PTFE rotating shaft seals are to be installed dry.

Among the advantages PTFE offers:
• Low friction
• Minimal parasitic drag
• Able to be used in applications with dry operation or insufficient lubrication
• Excellent thermal properties with an operating range of -130° C to +200° C
• High chemical resistance
• Low breakaway torque after standstill

Victor Reinz timing cover sets and rear main bearing seal sets are backed by Dana, supplying original equipment manufacturers the world over. Victor Reinz gaskets are now available in North America directly from their manufacturer, Dana.

Coolant Leaks
Coolant leaks can occur anywhere in the cooling system. Nine out of 10 times, coolant leaks are easy to find because the coolant can be seen dripping, spraying, seeping or bubbling from the leaky component. The first symptom of trouble is usually an engine overheating, but the vehicle may also have a low coolant indicator lamp. If you suspect the vehicle has a coolant leak, visually inspect the engine and cooling system for any sign of liquid leaking from the engine, radiator or hoses. The color of the coolant may be green, orange or yellow depending on the type of antifreeze in the system. You may also notice a sweet smell, which is a characteristic odor of ethylene glycol antifreeze.

Common Coolant Leaks
Most cooling systems today are designed to operate at 8 to 14 psi. If the radiator can’t hold pressure, the engine will overheat and lose coolant.

Water pump: A bad shaft seal will allow coolant to dribble out of the vent hole just under the water pump pulley shaft. If the water pump is a two-piece unit with a backing plate, the gasket between the housing and back cover may be leaking. The gasket or O-ring that seals the pump to the engine front cover on cover-mounted water pumps can also leak coolant. Look for stains, discoloration or liquid coolant on the outside of the water pump or engine.

Hoses: Cracks, pinholes or splits in a radiator hose or heater hose will leak coolant. A hose leak will usually send a stream of hot coolant spraying out of the hose. A corroded hose connection or a loose or damaged hose clamp may also allow coolant to leak from the end of a hose. Sometimes the leak may only occur once the hose gets hot and the pinhole or crack opens up.

Intake Manifold Gaskets: The gasket that seals the intake manifold to the cylinder heads may leak and allow coolant to enter the intake port or crankcase or allow it to dribble down the outside of the engine.

Intake Manifold

Intake manifold gaskets need to weather harsher environments than ever, including exposure to extended-life anti-freeze, also known as OAT (Organic Acid Technology) coolants. Victor Reinz intake manifold gaskets are built to stand up to today’s challenges, from engine design to coolant formulations to the “less than ideal” maintenance practices of many vehicle owners.

Victor Reinz upper intake manifold gasket sets contain the components needed to seal the joint between the upper and lower manifold sections. Lower intake manifold gasket sets contain the gaskets that seal the joints between the lower manifold and cylinder heads.

These are the worst kind of coolant leaks because they are hidden inside the engine and have the potential to cause the most damage.

Bad Head Gaskets: Internal coolant leaks are most often due to a bad head gasket. The head gasket may leak coolant into a cylinder or into the crankcase. Coolant leaks into the crankcase dilute the oil and can damage the bearings in your engine. A head gasket leaking coolant into a cylinder can foul the spark plug and create white smoke in the exhaust. Adding sealer to the cooling system may plug the leak if it is not too bad, but eventually the head gasket will have to be replaced.

Head gasket failures are often the result of engine overheating (which may have occurred because of a coolant leak elsewhere in the cooling system, a bad thermostat, or an electric cooling fan not working). When the engine overheats, thermal expansion can crush and damage portions of the head gasket. This damaged area may then start to leak combustion pressure and/or coolant.

There are several ways to find out whether or not a cooling system is holding pressure. One is to top off the cooling system, tighten the radiator cap and start the engine. When the engine reaches normal operating temperature, turn on the air conditioner (to increase the cooling load on the system) and/or take it for a short drive. Then check the radiator, hoses and water pump for seepage or leaks.

Leak detection dye can also be added to the coolant itself to make a slow leak easier to find. Some of these dyes glow bright green or yellow when exposed to ultraviolet light. If head gasket failure is the concern, a bore scope placed through a spark plug hole will quickly reveal the presence of coolant.

Vacuum Leaks
Even the smallest leak in an intake manifold can cause a problem with the air/fuel ratio. The extra air is unmetered and can lean the fuel/air ratio leading to check engine codes and driveability issues.

Finding an intake leak can be time-consuming using your eyes and ears.
Intake manifold air leaks will suck in air, not expel it. What is sucked in will influence the fuel mixture and impact engine and emissions systems.
A smoke machine allows you to diagnose multiple leaks in less time compared to other methods. A smoke machine can pressurize the intake manifold and put smoke or vapor into the system. If there is a leak, you will see smoke come out.

Connect the smoke machine to a vacuum port like the supply line to the brake booster. Make sure to block the throttle body with the right-sized plug. Also, block off the PCV system.

Leaking injector seals can cause lean and misfire codes. Conventional testing methods often involve flammable gases or putting thick oils on the seals and looking for a change in rpm, but this test can’t be performed on engines where the intake manifold restricts access. Smoke machines can help spot these leaks without any disassembly.

Smoke coming from the oil filler or PCV system on an engine that is not misfiring could mean the bottom of the manifold is leaking or has cracked. It can also indicate worn valve guides or seals.

Victor Reinz Products

This article was sponsored by Victor Reinz Gaskets from Dana Aftermarket. For more information on Victor Reinz gasket kits and sealing solutions, visit

You May Also Like

Enhancing Efficiency and Streamlining Operations: The Benefits of Utilizing Nexpart Multi-Seller for Repair Centers

In today’s fast-paced automotive repair industry, staying ahead of the competition is crucial for repair centers to thrive. One key aspect that can significantly impact operational efficiency and customer satisfaction is the availability of OE, Aftermarket, Heavy Duty & Salvage parts. Here are just a few advantages of incorporating Nexpart Multi-Seller, a cutting-edge parts ecommerce

In today's fast-paced automotive repair industry, staying ahead of the competition is crucial for repair centers to thrive. One key aspect that can significantly impact operational efficiency and customer satisfaction is the availability of OE, Aftermarket, Heavy Duty & Salvage parts. Here are just a few advantages of incorporating Nexpart Multi-Seller, a cutting-edge parts ecommerce solution, into repair center operations. By embracing this innovative platform, repair centers can enhance their overall efficiency, streamline operations, and ultimately provide an enhanced experience for both technicians and customers.

Get your vehicle road trip ready with these summer tips 

Summertime is a great time to take your car out on the open road, but it’s also important to ensure that your vehicle is in tip-top shape. Regular preventative maintenance can help you avoid costly repairs and keep your car running smoothly. Make sure you’re ready with these helpful tips from Delphi Technologies. Chassis The

A Closer Look: Ignition Coils

OE coils are known for their high failure rates. Engine misfires, rough idle, a decrease in power under acceleration, poor fuel economy, and a check engine light are all signs of an ignition coil that has failed. Read along for more technical information on how to diagnose a failed coil, and why the original equipment

Engineering behind chassis: high and low-friction parts

What is overengineering? Overengineering is often described as designing a product or solution in an unnecessarily complicated way where a simple solution had been shown to have the same efficiency, or is even more effective than the original.  In the aftermarket world, the OE part is where the journey starts. It begins with testing and

A Closer Look: Turbocharger Operation and Installation

Turbocharger Overview With an effort to increase fuel efficiency, maintain performance and reduce emissions, vehicle manufacturers are adding turbocharged engines to their lineups at a significant rate. Over the next five years, the turbo service market will continue to experience substantial growth.  At a basic level, a turbocharger consists of just three major internal components:

Other Posts

Deciphering Engine Misfire Codes

When the fuel/air mixture ignites, many factors must be met to pass a misfire monitor.

Hybrid Vehicle Fluid Maintenance

There are opportunities your shop can’t pass up just because the car or SUV has a hybrid badge on the back.

Reflashing Power Supplies

A power supply to keep the system voltage consistent is a required piece of equipment to perform a reflash procedure.

Today’s Fuel Pressure Diagnostics

Direct injection pressure is measured with sensors, and you’ll need a scan tool to measure the signals