Spark Plug Replacement – UnderhoodService

Spark Plug Replacement

inspect coils
Inspect the coils and keep them in order. They can help to eliminate any diagnostic variables if there is a ­problem after plug replacement.

Every time a spark plug fires, the spark burns a few molecules of metal off the plug’s electrodes. Over time, this eats away the electrodes and rounds off their sharp edges. The erosion gradually increases the gap between the electrodes, which, in turn, increases the firing voltage required to generate a spark. Eventually the point is reached where the ignition system fails to produce enough voltage and the plug misfires.

Misfires are bad news because they cause a noticeable loss of power and fuel economy, and a less obvious but very measurable increase in unburned hydrocarbon (HC) emissions. The catalytic converter can take care of the extra HC up to a point, but a steady misfire can make the converter overheat. If the converter gets too hot, it may suffer irreparable damage resulting in a power-robbing exhaust restriction or a loss of efficiency (which will set a P0420 catalyst code).

Some Disassembly Required

Modern engines tend to have the spark plugs placed as close to the combustion chamber as possible. With twin cams, long runner intakes and other obstacles, access to the spark plugs can be difficult. Take your time and make sure you bill the correct hourly rate.

Inspect the Coils

Coils shouldn’t have any visible damage, and the boot should be fully seated. While assembling coils to the engine, disregard the coil if you notice any visible damage like a cracked coil housing, broken anti-rotational tabs or a broken connector. Any damaged part could lead to a premature failure, and a poorly seated boot could lead to engine misfire.

Thru-Bolts

Always apply the specified torque to the specified mounting thru-bolt. Loose thru-bolts could lead to failures under vibration. Overtightened thru-bolts could lead to a cracked coil mounting ear and/or premature thru-bolt failure.

spark plug electrode
Gap can be adjusted and measured on fine-wire spark plugs, just use the right tools and stay away from the center electrode.

Torque and Anti-seize

Always tighten plugs to OEM specifications. Overtightening plugs in aluminum heads will usually damage the threads in the cylinder head. Do not use anti-seize on plated plugs being installed in an aluminum head because anti-seize can change torque values. If the OE doesn’t use anti-seize, you shouldn’t either.

Be careful to avoid creating a path of least resistance by inadvertently leaving a greasy fingerprint or chemical residue on the spark plug insulator.

Gapping

For modern fine-wire spark plugs, don’t measure the gap because you could damage the center electrode. However, it’s still a good idea to inspect the new spark plugs for damage or defects. The majority of these plugs come pre-gapped from the factory.

aluminum spark plug heads
On modern aluminum heads, anti-seize can change torque values and cause the plugs to be overtorqued.

On these types of plugs, bending the ground electrode(s) can alter the geometry and thermal performance of the electrodes to the point of causing a misfire.

On older applications, gapping may still be required. Gapping specifications can be found in the service information or emissions tag under the hood. Gapping specifications can also be found in electronic and paper catalogs.

Measuring the gap requires the right tools. A coil-style gap gauge will work for copper core plugs. For fine-wire or precious metal plugs, a wire-type gauge is recommended.

If it is necessary to widen the gap, do so with a tool that only pulls back on the ground electrode without touching the center electrode or the porcelain. To close the gap on a plug, gently tap the plug, electrode first, on a hard surface.

With spark plugs lasting 100,000 miles, don’t skimp on the plug or the hours involved replacing them. Using less expensive plugs can lead to impaired ­performance sooner.

You May Also Like

Ignition System Do’s and Don’ts

Why do ignition systems give technicians problems when diagnosing ignition-related misfires? The answer is that some technicians use tests that might give inconclusive results or do damage to the coil or drivers inside a module.

One of the most basic circuits found on every gasoline powered vehicle is the ignition coil. This transformer takes low-voltage, high-amperage current and changes it into high-voltage current. It has two windings that are not physically connected. What does connect them is magnetism. The primary creates an electromagnetic field when system voltage is applied. When the power is turned off, the magnetic field collapses. The energy from the primary is transformed by the secondary windings into high-voltage power that can jump the gap between the electrodes of the spark plug; this is called inductance.

ECM Damage

Engineers have devised two strategies that can be called the “immune system” for the electrical system.

Voltage Drop Testing

The measurement of voltage is like the speed of the traffic.

Spark Plug Fouling

Understanding why spark plugs get dirty.

Understanding Stop/Start Charging and Starting Systems

The problem may not have been caused by a complicated reason, something simple may have caused the system not to work.

Other Posts

Tools To Service Serpentine Belts

Servicing the serpentine belt on some vehicles is a tough task.

Battery Charging and Diagnostics

Here are six tips to use when diagnosing a vehicle with a dead battery. 

Why Do Timing Chains Stretch?

As the timing chain wears, it can change the timing of the camshaft and crankshaft.

Mayhew Tools Introduces Spark Plug Thread Chaser

This tool is made in USA and is backed by a lifetime warranty.