Safe Shop: Waste Oil Collection – UnderhoodService

Safe Shop: Waste Oil Collection

As an automotive repair shop, your business handles used oil and fluids daily, and there are certain good housekeeping practices that must be followed. These required practices, called “management standards,” were developed by the EPA for any business that handles used oil. These standards are common sense, good business practices designed to ensure the safe handling of used oil, to maximize recycling and to minimize disposal.


  • Properly label ALL containers and tanks for used oil.
  • Never store used oil in anything other than tanks and storage containers.
  • Keep all containers and tanks in good condition. Don’t allow tanks to rust, leak or deteriorate. Remove and replace any defective tank or container immediately!
  • Take steps to prevent leaks and spills. Have sorbent materials available on site should a leak or spill occur. Write an emergency response plan, post the instructions in a visible spot and properly train all employees in the procedures.
  • If a leak occurs, stop the oil from flowing at the source. If the leak can’t be stopped, put the oil in another container or tank.

    If a spill occurs, contain the spilled oil by spreading a sorbent material over the spill. Remember, all leaked or spilled oil collected during cleanup must be handled as used oil.

It’s permissible to mix any of the following fluids and handle them as waste oil:


Waste Motor Oil
Power Steering Fluid
Transmission Fluid
Gear Oil
Hydraulic Oil

Store each of the following fluids separately. DO NOT mix any of these with waste oil:

Cleaning Solvents
Brake & Carburetor Cleaners
Parts Washer Solvent

It is illegal to discard waste oil in a dumpster, down a sewer, in the water or even on the ground. Waste oil is regulated because it contains benzene and lead, picked up during the operation of a vehicle. Safe management and proper disposal of waste oil protects drinking water, fish, land and every worker in the shop!

Safe handling of used oil begins with using the proper equipment. There are two steps to follow when handing used oil in the shop. The first step is draining the used oil from the vehicle into a used oil collection container. The second step is transferring the used oil from the collection container into a bulk used oil holding tank.

Used oil collection containers or oil drains are available in a number of sizes and variations that can be used to transfer the used oil to the bulk holding tank.

One of the safest and most reliable ways of transferring used oil from an oil drain is by using a bulk system that incorporates an air-operated diaphragm pump and quick disconnect dry break couplers. This method pumps the oil quickly and safely from the drain into the holding tank. Most of these bulk systems are equipped with high level shut-off valves that prevent the tank from overflowing. And, most high volume drains — 16 gallons to 27 gallons can be modified to work with this type of system.

If the pump system is not an option, then a self-evacuating drain is another good choice. Instead of an air diaphragm pump, these drains use very low air pressure to transfer the oil out of the drain and into the holding tank. These drains are also available in high volume sizes. Source: JohnDow Industries

You May Also Like

Auto Value, Bumper to Bumper Ultimate Vehicle Giveaway

Two lucky technicians will win a vehicle of their choice this spring.

Auto Value and Bumper to Bumper are revving the engines in 2023 with the Ultimate Vehicle Giveaway promotional sweepstakes this March and April.

“Two lucky grand prize winners will get to choose an ultimate new vehicle.  Maybe a new sports car, a new pick up, or even an all-terrain vehicle. said Jim Holik, director of marketing for the Aftermarket Auto Parts Alliance, Inc., program headquarters for Auto Value and Bumper to Bumper. “We are always ready to fuel some excitement for our technicians and this Spring it’s going to be legendary.”

SMP Expands Hybrid and EV Product Offering

Standard is prepared to meet the demand of the growing hybrid and EV population with over 4,000 parts available for 150 models.

Mitchell 1 Adds Google Campaigns to its SocialCRM

Shops can share positive reviews and testimonials directly to a Google business profile or Facebook page.

ASE, Goodguys Partner to Promote Education, Careers

They are joining forces to showcase the wide array of career paths in the world of hot rodding and automotive service.

SMP Introduces 276 New Part Numbers

Included in the release is new coverage for 77 product categories.

Other Posts

Mitchell 1 to Hold Shop Management Workshop in Orlando

Registration now open for two-day training event.

Continental Offers 12 New Blower Motor SKUs 

Applications deliver late-model coverage for 20 popular import and domestic vehicles.

Dorman Launches New Repair Solutions

Among the new releases are Dorman OE FIX repair solutions designed to help save time, money or increase reliability.

Opus IVS Announces Launch of Master Class Free Training Series

Seminars and coursework focused on advanced vehicle technologies for those wishing to advance their skills.