Replacing a Decoupler Pulley Replacement (VIDEO)

Replacing a Decoupler Pulley (VIDEO)

Millions of vehicles have decoupler pulleys, heres how to replace them. This video is sponsored by Litens.

Almost every late model car or truck is equipped with an overrunning alternator pulley (OAP) or an overrunning alternator decoupler (OAD). An OAP is a one-way clutch like a socket wrench that turns in one direction and locks when turned the other direction. An OAD operates in the same manner, but has a special clutch and spring that absorbs vibration to smooth out vibrations in the drive belt system. Regardless of the type, the pulley should be checked before condemning and removing the alternator.

These new pulleys allow the alternator to “free-wheel” or “overrun” when the belt suddenly slows down. This prevents the belt from slipping and reduces vibration. Best of all, the system need less tension and even a narrower belt can be used. This can result in a 1.5% to 2% fuel economy improvement. However, these pulleys have a limited lifespan due to how they operate internally.  

OADs and OAPs behave the same, except the OAD will have a “spring feel” because of the internal spring. Testing can be performed on the vehicle with the belt attached.
1. Raise engine speed to 2,000-2,500 rpm in Park (auto trans) or Neutral (manual trans) and then shut off the engine. Listen for any noises from the OAD after the engine is shut off. A worn-out bearing will generate a “buzz” noise during this test. If the OAD is noisy during this test, replace it.
2. Remove the cap, and with the proper tool inserted into the front of the OAP, rotate the alternator’s shaft in both directions. In the overrun direction it should feel smooth and in the drive direction it should have a spring feel.
• If the pulley is locked up, replace it.
• If the OAD has no spring feel in the drive direction, replace it.
• If the OAD requires more than 9-13 in./lbs. (1-1.5 Nm) of torque to turn in the overrun direction, replace the OAD.
• If the OAD is not smooth in the overrun direction, replace it.

In this video, we cover the replacement technique for decoupler pulley for both on and off the engine.

This video is sponsored by Litens.

You May Also Like

The Vital Nature of Multi-V Belt Systems

From the alternator to A/C, the multi-v belt uses a truck’s engine to operate crucial components. Here’s how to keep things running smoothly.

You hop in the cab to start up your truck and notice — uh-oh… something doesn’t sound quite right in the engine compartment. If left unchecked, it could wind up with you stranded on the side of the road, in need of service. But what could it be? Let’s Pop The Hood and take a look.

Navigating The Legal Landscape with Succession Planning

Planning for a successful business handover means doing things by the book.

AMN Drivetime: Cal Ganda’s Continental Journey

Ganda embodies servitude leadership, prioritizing team success and customer-centricity.

Replacing Your Power Steering Reservoir

Discover why simply flushing out contaminants from power steering reservoirs may not be sufficient to prevent potential failures.

Planning for Your Shop’s Success In The Future

Understanding succession planning before you need it is critical. This series is presented by Standard.

Other Posts

The Autel IA900

Take an in-depth look at the Autel IA900 Alignment and ADAS calibration frame solution.

Troubleshooting Remote Keyless Entry and Vehicle Starting Issues

Learn how key rings, RFID chips, and other factors can affect your vehicle’s security system and learn to resolve these problems.

Choosing the Right Power Steering Fluid

Learn what power steering fluid is, why it’s crucial for your customers vehicle, and how to choose the right type.

What Causes the White Crystals in an SCR System?

This video covers how detergents and surfactants in Diesel DEF Medic Plus clean the DEF system. This video is sponsored by Rislone.