Relearn Procedures Require TPMS Tool – UnderhoodService

Relearn Procedures Require TPMS Tool

Most vehicles require some type of "stationary" relearn procedure to reset the TPMS system. This requires a TPMS tool to activate each of the tire pressure sensors in a specified sequence so the TPMS control module can relearn their new locations.

Most vehicles require some type of “stationary” relearn procedure to reset the system. This requires some type of TPMS tool to activate each of the tire pressure sensors in a specified sequence so the TPMS control module can relearn their new locations. On some GM applications, a J-41760 magnetic tool is required to “wake up” the sensors. On most other applications, a factory TPMS tool or an aftermarket TPMS tool that broadcasts a radio signal is needed for the sensor position relearn procedure.
 
On some applications, the TPMS relearn tool can be connected to the vehicle’s OBD II diagnostic connector to read and clear codes, display system data and perform sensor ID programming. On many Asian and
European applications, each individual tire pressure sensor has a unique ID code. Vehicles that currently require this kind of reprogramming include most Hyundai, Infiniti, Kia, Lexus, Mitsubishi, Nissan, Subaru, Suzuki and Toyota models. If one or more sensors have been replaced, the new ID information has to be input directly into the system. So if you don’t have a TPMS tool that can do this, your only alternative is to send your customer back to the new car dealer to have the ID reprogramming done.
 
TPMS relearn procedures vary a great deal from one vehicle to the next, so you also need access to the TPMS service data for the vehicle, or a reference manual or chart that covers the relearn procedures. Without this vital information, you can’t reset the system.
 
Essentially, most relearn procedures require you to put the system into a relearn mode. On some, this may require a command from a scan tool or plug-in TPMS tool. Or, you may have to cycle the ignition key on and off a certain number of times while stepping on the brake pedal. On others, the keyless entry fob may be used to wake up the TPMS module and ready it for relearning.
 
When the TPMS is ready, it may signal by beeping the horn or flashing the hazard lights. The TPMS activation tool is then placed near one of the tire pressure sensors, and a button is pressed for five or six seconds to wake up the sensor. As soon as the TPMS module recognizes the sensor and learns its position, the system signals again by beeping the horn or flashing the hazard lights. You then repeat the same procedure for each of the remaining tire pressure sensors in the specified order until the relearn procedure is complete.
 
Even on vehicles that have a key fob or driver information center relearn procedures, scan or dedicated TPMS tools that can interface through the OBD II connection can have advantages when it becomes to difficult to reprogram vehicles. 
 
With some procedures using a J-41760 magnetic tool, you are flying blind. Problems with the key fob, antenna and even the module or serial data bus connection can leave you chasing your tail. With a scan or dedicated scan tool, it is possible to perform a more accurate relearn and diagnosis and problems.  

You May Also Like

Mercedes Ignition Coil Pack Diagnostics

Replacing a single coil might not be the best approach to curing an engine of a chronic misfire.

In a perfect world, a flashing check engine light for DTCs P0301 through P0312 would always be solved by installing a new ignition coil. If this were true, technicians would not need countless hours of training. However, the reality is that a misfire can be more than a missing spark from an ignition coil. Also, replacing a single coil might not be the best approach to curing an engine of a chronic misfire.

Chrysler’s Totally Integrated Power Module

The TIPM is on the CAN bus, any issues with the communication between the ECM, ABS and BCM can cause problems with the TIPM.

Mercedes EQS Service Opportunities

EQ is the EV brand for Mercedes. It is the equivalent of Audi’s Etron or VW’s iD brands.

ADAS Calibration Tips

Here are 10 tips to follow during ADAS Calibration.

Chassis Control Modules After Reconnecting Battery

To resolve the issue, fully disconnect the negative lead from the battery terminal.

Other Posts

Tesla Model 3 TPMS Service

Resetting and programming TPMS sensors for a Tesla is a lot like any other vehicle, and the challenge is still the same: keeping the light off.

Power Window Regulator and Motor Service

Power windows are great as long as they roll up and down when commanded to do so.

TPMS Tools and Sensors

Transform TPMS with advanced diagnostics and sensor programming. This video is sponsored by Bosch.

Caring For AGM And Flooded Car Batteries

Faulty battery cables, if loose, corroded, or damaged, can lead to power drainage.