Performing An Alignment On VW Jetta And Golf Vehicles – UnderhoodService

Performing An Alignment On VW Jetta And Golf Vehicles

Most entry-level VW models featured the same basic suspension used from the advent of the original VW Rabbit. About the only change was from a rear strut suspension to a separate coil spring and shock absorber in the rear. Used for all models of the Golf, Jetta, New Beetle and the Audi TT, this suspension is simple, durable and easy to repair. There is still a beam axle in the rear of pre-2006 FWD cars.

Most entry-level VW models featured the same basic suspension used from the advent of the original VW Rabbit. About the only change was from a rear strut suspension to a separate coil spring and shock absorber in the rear. Used for all models of the Golf, Jetta, New Beetle and the Audi TT, this suspension is simple, durable and easy to repair. There is still a beam axle in the rear of pre-2006 FWD cars.

For 2006, the A5 platform went to a multi-link rear suspension design that resembles the Ford Focus down to the blade-shaped upper control arms. Also, the front suspension knuckles resemble the Ford Focus design.

Beam Axles
Pay attention to the alignment angles, like toe and camber, for an indication of the health of the axle. Very few cases of corrosion have been reported with VW beam axles. The most common failure involves the bushings that connect the rear axle to the body. Bad bushings cause noise, thrust angle and setback problems.

Check the rear spring insulators for damage and dry rot. Also, make sure the lower bushings and upper shock mounts do not show wear or signs of bottoming out.

The majority of beam axle vehicles can be adjusted by inserting a shim between the axle and wheel bearing hub unit. This can offer some degree of adjustment. If the axle is way beyond adjustment, replacement is necessary.

Multi-Link Rear Suspensions
The VW A5 platform for the Golf, Jetta and Audi TT abandoned the rear beam axle for a multi-link system with trailing and lateral links. The main wear points of the suspension are the bushings. Check for wear and any signs of movement in outboard upper and lower control arms. As the bushings age, the extra compliance can cause toe and camber angle to exceed specifications.

The A5 platform has adjustment built into the rear suspension. An eccentric bolt on the upper control arm’s inboard mount controls the camber. The lower lateral link’s inboard bushing includes an eccentric to adjust the toe.

Front Suspension
In the front, all Jettas and Golfs have a very basic strut assembly with a lower control arm with two inner bushings and a bolted-on ball joint at the bearing carrier. Nothing could be simpler; even the sway bar is relatively easy to remove and install.

About the only weak points are the ball joints, as they are tiny and, with the additional horsepower, larger wheels, tires and brakes, they are prone to failure.

The fourth-generation platform was known to have problems with the suspension cradle shifting and changing the suspension angles. Often, the bushings are to blame. Some customers may complain of a popping or banging during turns in the foot well area. Oil and transmission fluid leaks can often cause the bushings to fail. Before replacing these bushings, make sure the leaks are resolved.

The A5 or fifth generation platform also had suspension sub-frame complaints. The driver may complain of popping or banging in the foot well area. The problem is often the fasteners that hold the sub-frame to the body. These bolts are torque-to-yield bolts that can work loose over time. This allows the sub-frame to move against the body and cause noise. If you see a case of this, it is recommended to replace the bolts and re-torque bolts using the proper procedure.    

With every generation of the Jetta and Golf, the method of adjusting the camber has gone from easy to difficult to impossible. On pre-1998 vehicles, the camber could be adjusted by slotting the lower strut mounting bolts or by the use of a cam bolt. In 1999, VW said the camber was not adjustable, but could be changed slightly by moving the engine cradle. But, some aftermarket companies introduced upper strut mounts that could change the camber by ±1º. In 2006, the only way to change the camber was by shifting the sub-frame.

If you do see a late model VW with the camber out of specification, look for damaged parts first.  

Steering Angle Sensors
After a minimal alignment, it is not required to reset the steering position sensor with a scan tool. The lateral accelerometer and yaw sensor will compensate for minor changes in the steering angle after one drive cycle. If an extreme toe angle adjustment was performed or if steering column and/or rack was replaced, it is required to perform a calibration procedure.

On vehicles with HID headlights, there is a link on the left front control arm that controls the angle of the lights depending on the attitude of the vehicle. The link is prone to damage and become detached. Always inspect this linkage and replace if necessary. Also, the sensor can be calibrated with a scan tool. 

 

You May Also Like

Nearly 5,000 To Participate In Auto Value, Bumper To Bumper ‘Festive Walk’ To AAPEX 2018

On Thursday, Nov. 1, nearly 5,000 Auto Value and Bumper to Bumper automotive professionals wearing matching yellow shirts will begin their “festive walk” from the Mirage hotel to AAPEX 2018 at the Sands Expo, temporarily shutting down the busy Las Vegas Boulevard along the way.

On Thursday, Nov. 1, nearly 5,000 Auto Value and Bumper to Bumper automotive professionals wearing matching yellow shirts will begin their “festive walk” from the Mirage hotel to AAPEX 2018 at the Sands Expo, temporarily shutting down the busy Las Vegas Boulevard along the way.

The group is scheduled to depart at approximately 8:30 a.m. (PDT) and start arriving at AAPEX for their day-long visit around 9 a.m. The group will include parts store operators, shop owners, technicians and service writers who are part of the Aftermarket Auto Parts Alliance. Las Vegas showgirls and a marching band will join in the festivities as the group makes its way to AAPEX.

Drive Belt Checklist: What Are You Missing?

You might have only one chance to sell a customer a new serpentine belt. With belts lasting roughly 90,000 miles, proper inspection at the time of failure is critical not only for selling the belt, but also for ensuring add-on sales and better customer satisfaction.

3 Reasons To Replace Cabin Air Filters In Winter

Often driven by an “out of sight, out of mind” mentality, most consumers don’t think about purchasing cabin air filters. That’s why educating consumers on the benefits of cabin air filters can be a shop’s best sales pitch for selling these maintenance add-ons.

VIDEO: Using Airflow To Sell Cabin Air Filters

Andrew Markel introduces an inexpensive tool that can assist in selling cabin air filter replacements. Sponsored by Auto Value and Bumper to Bumper.

airflow-selling-cabin-air-filter-video-featured
Air Conditioning Odor Causes

Air conditioning odors typically result from the uncontrolled growth of bacteria and other microorganisms in the evaporator. Research by independent laboratories has found fungi such as Aspergillus, Cladesporium, Penicillium and others growing on cooling coils and other A/C system areas.

ac air conditioning smells featured

Other Posts

Dorman Launches 300+ New Products In November

Among the new products is an OE FIX climate control module designed to fit 1.7M Chevrolet Express & GMC Savana vehicles.

Curing Springtime Air Conditioning Smells

Air conditioning scents can come from a host of things.

VIDEO: Wheel Bearing Preload And Load Paths

If you’re replacing a wheel bearing, you should also check the alignment. This video sponsored by GMB.

Looking At Alignment – From A Few Different Angles

Independent shops that are investing in modern alignment equipment are quickly realizing the profit potential it offers.