Installing Subaru Stretch Belts

Installing Subaru Stretch Belts

When a stretch belt exceeds wear specifications, it's no longer able to grip the pulleys and will start slipping.

If you see a belt on a late-model Subaru does not have an automatic tensioner and runs between only two or three components, it’s probably a stretch belt. You may also notice some belts will have the words “stretchy” or “stretch” written on the back. These types of belts typically are used to turn the A/C compressor on the 2.5L four-cylinder engine in 2008 and up models.

The stretch belt can help to simplify the serpentine belt system on the Boxer engine. It can also increase the efficiency of the engine by allowing it to run with less tension on the alternator and power steering. Beyond that, it can extend the life of the alternator by reducing the load on the bearings.

Subaru stretch belts can last 100,000 miles or more. On a worn belt, the cracks or damage to the backing of the belt will not be evident to the naked eye. This is why an inspection method measuring groove depth is recommended — you simply cannot go by mileage recommendations alone.

Inspection

When inspecting a stretch belt, always measure the depths of the groove with an inspection tool because the differences between a worn belt and a good belt can’t be seen or felt. The new materials used to manufacture a stretch belt will not crack or separate like older belts before the grooves are worn. Belt inspection gauges are available from manufacturers and distributors, so check their websites or ask your distributor if you’re in need.

Poor pulley alignment is the No. 1 cause of belt noise and premature wear of stretch belts. If the pulleys have poor alignment, the belt will be worn on the edges and might look frayed.

Alignment problems can stem from issues with shaft endplay in an A/C compressor or crankshaft. Alignment problems can also indicate a worn A/C clutch or a crankshaft pulley/dampener that is about to fail. Also note that leaking seals can contaminate the belt.

Worn Belts

When a stretch belt exceeds wear specifications, it’s no longer able to effectively grip the pulleys and will start slipping. The primary cause of this slippage is when material is removed from the belt’s grooves, rather than it stretching and losing tension.

Over time, small debris and the interaction with the pulleys will wear the shoulders and valleys of the grooves. When the grooves become too shallow, the pulleys bottom out. When this happens, the walls of the groove can no longer grip the pulley and it slips.

If you are removing an old stretch belt from a Subaru, just cut it. Even if the belt is still in excellent shape, the act of pulling the belt over the A/C compressor clutch or crankshaft pulley will damage the inner core.

These belts have a thermo-elastic core designed to keep tension on the pulleys during a long lifecycle. The material acts like shrink tubing for a wiring harness. Once the belt has been run and exposed to the underhood temperature, the heat will decrease the length of the belt and, therefore, properly tension it.

Never use a screwdriver or other sharp object to install the belt because if the belt is cut or the surface or grooves of the pulleys are damaged, the belt will eventually fail. Special tools are available from various tool and belt manufacturers that act as a ramp on the leading edge of the pulley. Some applications will require special tools to hold the belt on the accessory pulley, as is the case for the Subaru A/C compressor pulley.

There are many tool designs, but they all perform the same task of pulling the belt over the leading edge of the crankshaft pulley without damaging the belt. Always follow the directions for proper tool placement and for the correct direction to turn the crankshaft. After the belt is installed, confirm the belt is in the grooves and recheck there are no alignment problems. Run the engine for a few seconds before doing this final check.  iC

You May Also Like

Supercharger Pros And Cons

Customers generally look to superchargers for the instant throttle response, not fuel economy.

Superchargers are synonymous with making horsepower, especially in drag racing, gaining popularity and recognition as a viable power adder. However, they’re not the best option for saving fuel.

While most automakers are currently fascinated with employing turbochargers to make up for lost horsepower due to lower-displacement engines, do superchargers have a place in the current automotive climate? Indeed, this power-adder is more commonly found in the performance arena, because it produces power at lower rpm and comes in a smaller package than a turbocharger. But there are some downsides.

Plastic Timing Chain Guides

Timing chain guides are designed to wear, but the guides are designed to last the engine’s life.

It’s Got Spark!

Why can’t you trust some spark tests?

Honda Electronic Throttle Body Service Tips

Using care and following OEM procedures will help you to avoid unnecessary parts replacement and comebacks.

Belts and Pulley Alignment

A misalignment of the plane of the belt can occur when a pulley is not parallel to the other pulleys on the belt drive system.

Other Posts

Inspection Tips For Chain-Driven Water Pumps

If one water pump fails sooner and is replaced without an investigation, the new pump is likely doomed.

Water pump feature
Diagnosing Misfires

What if there are no codes and a misfire is intermittent? This is where it gets complicated.

Lifter Deactivation

The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine.

Alternator Testing For No Charge Conditions

Many alternator problems turn out to be nothing more than a bad connection at the alternator or a bad wiring harness.