Inspect The Automatic Transmission Filter And Fluid – UnderhoodService

Inspect The Automatic Transmission Filter And Fluid

Changing the automatic transmission filter and fluid is a great preventive maintenance practice, ensuring a clean and proper working transmission assembly. The most important factors are installing the correct filter for the vehicle application and the correct installation procedures of the filter. An incorrect filter installation or the wrong filter will ultimately cause erratic shifts and possibly cause damage to the transmission assembly.

Changing the automatic transmission filter and fluid is a great preventive maintenance practice, ensuring a clean and proper working transmission assembly. The most important factors are installing the correct filter for the vehicle application and the correct installation procedures of the filter. An incorrect filter installation or the wrong filter will ultimately cause erratic shifts and possibly cause damage to the transmission assembly.

 
Some, if not all transmission filters, are equipped with what is known as a lip seal. Installing the filter with the lip seal as a unit will not seat the filter properly, cause ingestion of air around the lip seal and dislodge the filter from the pump bore.
 
The most common cause of transmission erratic shifting after a filter and fluid service is the ingestion of air. When air is introduced inside automatic transmissions, a customer will notice: transmission slippage after 3 to 5 miles of driving; the vehicle will stall or engine will shut off when coming to a stop, or an MIL light illuminates, setting an incorrect pressure ratio DTC.
 
So where is the problem? We cannot condemn the transmission clutch assemblies because of slippage, nor can we blame the torque converter because of the stalls and engine shut offs and, finally, we cannot say that the pressure regulator solenoid or valve is stuck or worn because of a trouble code.
What to do now? Let us follow the first three important steps:
1. Hear the customer’s complaint;
2. Check the level of the ATF; and
3. Test drive the vehicle. 
Now that we have done all three and have encountered a problem, let us pull that good ol’ pressure gauge from the toolbox. A scan tool will not help you in this situation. Once you have connected the pressure gauge and the vehicle is running, any rapid fluctuations of the gauge needle, vibration or humming of the gauge indicates that the pump maybe pulling air.
 
How can we assume that the pump is pulling in air? Easy: Overfill the transmission with ATF! Overfilling the transmission with fluid raises the fluid level beyond the area to where the air is being introduced. Also, pay attention to the pressure gauge; the needle of the gauge will smooth out once you have overfilled the transmission and no air is present.
 
Now that we know that air is being pulled into the transmission, we have to find the source. The removal of the transmission pan is now required. We have to make sure that the filter’s rubber lip seal was not damaged when it was driven up into the pump bore. If the filter is attached to the valve body, gently apply downward pressure of the filter’s body to see if the filter is properly lodged into the lip seal. Inspect the filter for any cracks or separation of the seams.
 
Article courtesy of ATP TechDirect.

Bulletin No. 11-1007 
To: All ATP Technicians
 
 

You May Also Like

Acura Turbo Engine Service

It is important to check the operation of the solenoids that control vacuum to the actuators.

The 2007-2012 Acura RDX was Honda’s first production vehicle in North America with a turbocharger. The company took the proven K-series engine and lowered the compression ratio from 10:1 to 8:1, and added a turbocharger with the associated plumbing. But, it is a lot more complicated when it comes to managing the boost.

Subaru EJ25 Head Gasket Problems

Most of the EJ head gasket failures occur around the 100,000-mile mark and start as a slow oil or coolant leak.

Honda Electronic Throttle Body Service Tips

Using care and following OEM procedures will help you to avoid unnecessary parts replacement and comebacks.

New Oil Specifications

Many 0W16 oils have a new donut certification mark on the bottle called API SN-PLUS and SN-PLUS Resource Conserving.

Solving Intermittent Overheating

New cooling systems anticipate and influence changes in coolant temperature.

Other Posts

Hyundai & Kia Hybrid Drivetrain

The Hyundai hybrid system has a motor control unit (MCU) and hybrid control unit (HCU).

Ignition Systems

The ignition coil is a very simple and robust circuit.

Alternator Testing For No Charge Conditions

Many alternator problems turn out to be nothing more than a bad connection at the alternator or a bad wiring harness.

Lifter Deactivation

The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine.