Engine Tech Tip: Measuring Blowby – UnderhoodService

Engine Tech Tip: Measuring Blowby

You’ve built an engine exactly the same as the last engine, but the power seems to be down 10 to 20 horsepower on the dyno. Could it be excessive blowby because of a ring sealing problem? One way to find out is to measure crankcase blowby.

By Larry Carley
Technical Editor

You’ve built an engine exactly the same as the last engine, but the power seems to be down 10 to 20 horsepower on the dyno. Could it be excessive blowby because of a ring sealing problem? One way to find out is to measure crankcase blowby.

A blowby flow meter can tell you precisely how much blowby is occurring inside the engine. Unlike a cranking compression test or a static leakdown test, a blowby test actually measures the volume of gases that are entering the crankcase past the piston rings. The flow meter allows you to measure blowby from any engine speed, all the way from idle to wide-open throttle.

A blowby test requires a blowby flow meter. The meter measures airflow, and is attached to either the crankcase vent on a valve cover breather, or the PCV valve fitting. On a V6 or V8 engine, the opening on the opposite valve cover must be temporarily blocked so all the airflow from the crankcase will flow past the meter.

When the engine is running, all blowby that leaks past the rings will flow through the crankcase, out the valve cover opening and through the blowby flow meter sensor. The meter outputs an analog voltage signal that ranges from zero to five volts. The display can then be converted into units that show you the volume of airflow per unit of time. Most engine builders typically display the reading in cubic feet per minute (cfm), though heavy-duty engine builders more often use cubic feet per hour (cfh).

One supplier of blowby flow meters said contrary to what many people think an engine typically has more blowby at idle than at higher rpms. As the speed goes up, the rings actually seal better and blowby drops.

How much blowby is normal? Dividing an engine’s maximum horsepower output by 50 will give you a ballpark number for how much blowby you would normally expect to see. For example, a street performance engine that makes around 500 horsepower will typically have about 10 cfm of blowby with conventional pistons rings and ring end gap tolerances. Higher performance engines that are built to tighter tolerances will usually have less blowby, as might those with gapless piston rings. An 800 to 900 horsepower NASCAR motor, for example, might only have 5 cfm of blowby.

Less blowby means more usable horsepower. Being able to baseline the actual blowby in an engine means you can then go back and try different ring configurations, ring types (conventional or gapless), different ring end gap settings and cylinder wall finishes to see which combination gives the best seal and the least amount of blowby.

Measuring blowby has been one of the best kept secrets with performance engine builders because it allows them to see how well the rings are or are not sealing. It also allows them to detect any ring flutter that may be occurring within a particular rpm range, and to then change the mass or end gaps of the rings to minimize the problem.

You May Also Like

FLO, GM Activate Plug and Charge for GM EV Drivers in Canada

FLO’s technology confirms identification, authorizes the charging session and activates billing without any additional action from the driver.

FLO and General Motors activated the Plug and Charge capability at all DC fast chargers on the FLO network across Canada. All GM EV drivers are provided with access to GM’s Plug and Charge, which is enabled by FLO’s autocharge software. The feature allows GM EV drivers to begin a fast-charging session by plugging in their vehicle at one of FLO’s fast charging stations across Canada, the company said.

Schaeffler and Sustainability with Jerry Conroy

Conroy shares insights into his career trajectory, the evolving landscape of the company’s aftermarket operations, and its commitment to innovation and sustainability.

Flushing the Brake Fluid is Critical on Every Brake Repair

Making sure the brake fluid is the correct quality is critical. Sponsored by Auto Value and Bumper to Bumper.

Selecting the Right Oil for your Customers Engine

Learn how to educate customers on the importance of OEM specifications and premium lubrication for their vehicles’ maintenance needs.

At the Intersection of Tradition and Innovation with Grace Hovis

Grace Hovis’s journey in Hovis Auto & Truck Supply blends tradition with digital innovation in the automotive aftermarket industry.

Other Posts

Inspection Tips For Chain-Driven Water Pumps

If one water pump fails sooner and is replaced without an investigation, the new pump is likely doomed.

Water pump feature
Power Window Regulator and Motor Service

Power windows are great as long as they roll up and down when commanded to do so.

Philips Announces GoPure GP5212 Automotive Air Purifier

It uses a 3-layer filter to deliver cleaner, healthier, fresher air on the go, Lumileds said.

Snap-on Announces Latest Software Release

The latest software includes new coverage and guided component tests and features.