Brake Job: 2000-2007 Ford Focus – UnderhoodService

Brake Job: 2000-2007 Ford Focus

The 2000-2007 Ford Focus is based on the Ford global C1 platform, shared with the European Ford Focus and Volvo S40.  Nothing is really groundbreaking about the brake system. However, not paying attention to the details can end in a post brake job comeback.
Front Brakes
Pads should be replaced when there is 3mm or less of friction material. The rotors have enough material on them to last at least one turning on the lathe. The runout specification for these vehicles is .002” and disc thickness variation should be far below .0008”.
Front Anti-Rattle Clip
The calipers mount to the brackets using caliper guide pins with Allen heads. The sleeves  and boots should be disassembled, cleaned and lubricated every time the brakes are replaced. The torque for the guide pins is 21 ft/lbs and the caliper bracket bolts should be tightened to 75 ft/lbs.
Rear Brakes
The majority of Ford Focuses come with rear drum brakes. The only way to remove the drum without disturbing the wheel bearings is to remove the four mounting bolts on the bolts back of the trailing arm. The axle nut can be removed to pull the drum, but you will be disturbing the preload on the bearing. Also, the wheel hub retaining nut can be re-used only four times and requires a torque setting of 174 ft/lbs.
Rear Brake Load Sensor
The linings use an adjuster at the top of the drum under the wheel cylinder. Make sure the adjuster is clean, lubricated and the end that contacts the shoe is not worn.
On models with rear-disc brakes, Ford uses a hand-brake that is incorporated into the rear caliper. To service the caliper, remove parking brake cable and remove the lower bolt to swing the caliper upwards. The rear-disc brake cars require the familiar method of turning the piston while applying pressure.
The calipers mount to the brackets using caliper guide pins with Allen heads. The sleeves and boots should be disassembled, cleaned and lubricated every time the brakes are replaced. The torque for the guide pins is 21 ft/lbs and the caliper bracket bolts should be tightened to 55 ft/lbs.
Rear Brake Drum Adjuster
Most models were fitted with a PCRV valve fitted between the master cylinder and the rear brake lines to the rear wheels. The valves control the hydraulic pressure applied to the rear brakes, thereby reducing the risk of rear wheel lockup under braking.
Some models that were fitted with a rear brakes are fitted with a load sensing proportioning valve to control the rear brakes. It is mounted to the rear subframe and sway bar. The brake load sensor proportioning valve adjustment must be carried out with the vehicle in the correct ride height condition. The vehicle should be in an unladen condition and when the vehicle weight is on the road wheels. Also, the fuel tank should be full. If not, for every quarter the tank is missing, add 22 lbs. over the rear wheels.
Loosen the brake load sensor proportioning valve lever retaining nut and valve spring setting bar screw. Position the brake load sensor proportioning valve lever on the stabilizer bar so that the valve spring setting bar is central in relation to the setting bar screw.
Measure the dimension between the lower end brake load sensor proportioning valve spring hook and the groove on the valve spring setting bar; it should be 57mm. Set the brake load sensor proportioning valve spring setting bar to the correct position. While tightening the brake load sensor proportioning valve spring setting bar screw, make sure that the setting bar does not move. Tighten the brake load sensor proportioning valve spring setting bar screw.

You May Also Like

Transmission Line Replacement

Transmission fluid likes to be at a constant temperature. If it is too hot or too cold for too long, the performance can fluctuate and potentially cause damage to the transmission.

Transmission fluid likes to be at a constant temperature. If it is too hot or too cold for too long, the performance can fluctuate and potentially cause damage to the transmission.
If the fluid is at a constant temperature, it behaves in a consistent manner in terms of its friction and lubrication properties. What can help control the temperature is the transmission cooling circuit.
The path of the fluid in the transmission lines is not as much about the destination as the journey. The size and length of the transmission lines, along with the size of the cooler, controls the temperature of the fluid. Also, the size of the engine and weight of the vehicle can determine the design of the transmission fluid cooling circuit.
Another thing to consider is how a modified transmission with a larger transmission cooling circuit might do more damage than good. On modern vehicles, the cooling circuit is designed to manage the fluid temperatures during startup. If the fluid can’t warm up quickly due to the increased volume, damage to the transmission friction surfaces can occur. The same goes for a bypassed cooling circuit. Why? Because fluid that is too hot can damage friction surfaces.

VIDEO: AAPEX 2016 Insights

Andrew Markel discusses his take on conversations he had with economists at AAPEX 2016, including the future of purchasing parts.

BMW Tech Tip: Oil Separator Replacement

A clogged oil separator valve is a common problem on many BMW DOHC inline sixes. The high failure rate is caused by sludge build-up that can result in oil burning, rough idle and engine fault codes. Although the solution is pretty simple, replacing the valve is labor intensive and can take anywhere from six to nine hours.

New IDUSA Premium Guard Website Offers Easy Access To Wide Range Of Oil, Air, Cabin, Fuel And Transmission Filters

The new website’s bi-lingual, responsive design features look-up powered by ShowMeTheParts.

VIDEO: How To Deal With Air Conditioning Smells

Andrew Markel discusses what to do to get rid of A/C smells after customers have tried to do it themselves.

Other Posts

Oil Bath Air Filters

Long before people started using cotton gauze air filters soaked in oil, the oil bath air filter was the dominant filter on the market. The filter removes debris in the air by running it over oil and a mesh element. These filters worked great when most roads were dirt, but they could be messy to clean.

On The Web – September 2016

Finding Failing O2 Sensors If an O2 sensor gets “lazy” because of old age or contamination, the computer may not be able to adjust the fuel mixture quickly enough as the engine’s operating conditions change. Related Articles – Join Underhood Service On LinkedIn – Honda Tech Tip: Oil Pressure Switch Fails Intermittently – Fuel Trim

Join Underhood Service On LinkedIn

Related Articles – Check Out The August Issue Of Underhood Service Magazine – Hayden Automotive Introduces Low-Profile Fan Clutch – Belt Inspection Checklist                     Underhood Service’s LinkedIn Page                         Underhood Service’s LinkedIn Group    

Honda Tech Tip: Oil Pressure Switch Fails Intermittently

The MIL comes on with one of these DTCS: P3400 (VPS Stuck Off Bank 1) or P3497 (VPS Stuck Off Bank 2). This may be the result of the front and/or rear rocker arm oil pressure switch intermittently failing.