Auxiliary Water Pump Diagnostics

Auxiliary Water Pump Diagnostics

A car or truck comes into your shop with a complaint of poor heater performance. The driver complains that on cold mornings the heater will blow cold during the drive to work in rush hour traffic. The car is not overheating and the air is coming from the correct ducts. Your first reaction might be to install a new thermostat and inspect the heater core for a blockage. On the test drive, the system may perform great for you. Is the customer just cold blooded?

A car or truck comes into your shop with a complaint of poor heater performance. The driver complains that on cold mornings the heater will blow cold during the drive to work in rush hour traffic. The car is not overheating and the air is coming from the correct ducts.

Your first reaction might be to install a new thermostat and inspect the heater core for a blockage. On the test drive, the system may perform great for you. Is the customer just cold blooded?

The issue could be the auxiliary water pump. This pump is not connected to the cooling of the engine. Its primary function is to circulate warm coolant to the heater core. If too little coolant is circulated, the blower fan will pull enough heat out of the coolant and cause the heater core to get cold.

These pumps were first used on luxury and diesel vehicles in the 1990s. Most diesel engines typically do not generate a lot of heat when running or idling. Coupled with the lower engine speeds, the coolant in the heater core would lose most of its heat before it passed through to the outlet. This would frequently cause drivers to complain about insufficient heating if they drove in stop-and-go traffic or cruised at speeds with lower RPM. So, adding an auxiliary coolant pump would provide enough volume of coolant to keep the heater core warm.

Engineers then started to use these pumps on gasoline-powered vehicles for the same purpose. This allowed vehicle designers to use larger heater cores to provide better passenger comfort.

The control of the pump as part of the automatic temperature control system keeps the cabin heated even after the driver has turned off the ignition. The system can keep the interior warm for short periods of time while the driver goes shopping or grabs a bite to eat.

These pumps will show up on more and more vehicles as engines become more efficient and generate less excess heat. Also, new technologies like hybrid drives and stop/start systems need auxiliary pumps to not only improve driver comfort, but also to keep the batteries at a constant temperature.

Modes of Operation

Note that the auxiliary pump is not running all the time. The BCM or controlling module will control and regulate the pump using information like:
• Vehicle speed;
• Engine RPM;
• Coolant temperature;
• The temperature selected on the control head;
• Blend door position;
• Fan speed; and
• Exterior and interior temperatures.

If the vehicle has key-off control, there are additional parameters that must be met to activate the pump. These include:
• Battery voltage;
• Supply voltage to blower motor;
• Recirculation flap position;
• Security module input; and
• Keyless entry fob location.

A scan tool can test the pump function in most vehicles, but it is also possible to test the system by pressing an HVAC control head button sequence listed in the service information.

Causes of Failure

The main reason why these pumps fail is age and wear of the electric motor. Like all rotating electrical devices, brushes wear and windings short. Overheating can hasten the electric pump’s failure because increased cooling system pressures can force coolant past the shaft seals. Low coolant can also cause a pump to fail because of its position, which is typically high in the system, either on the firewall or strut tower.

Failure Modes

A failed pump will almost never cause the vehicle to overheat. If the auxiliary coolant pump is inoperative, the customer might notice reduced heater performance at low speeds and at idle.

Your first instinct might be to replace the thermostat, the water pump or the heater core, but if the vehicle is equipped with an auxiliary coolant pump, you will need to dig a little bit deeper with your diagnostic process.

Diagnosis

The tools needed to diagnose an auxiliary coolant pump include scan tool, meter and service information, with scan tools and service information being most important for late-model vehicles. The operation of the pump is dependent on several modules and numerous sensors that are networked.

The first step in the diagnostic process is to check for codes with a scan tool. Unrelated codes for collision detection, door module operation and loss of communications incidents can cause the deactivation of the pump. This is where service information can make the difference between a quick diagnostic process and parts swapping.

Newer vehicles may vary the voltage to control pump speed. Like all electrical devices on a vehicle, the operation is a balancing act between driver comfort and minimizing electrical loads on the alternator.

The cooling circuit on some vehicles with electric pumps may be called an auxiliary cooling circuit in the service information. The coolant may travel through the transmission cooler and windshield washer fluid bottle as part of the circuit on some Mercedes models.

Hybrids

Hybrids almost always have an electric water pump to cool the battery packs and inverters, and some hybrids will have a second pump for the heater core in the cabin. Hybrids or mild hybrids with stop/start systems not only have an auxiliary cooling pump, but also electric pumps for the oil and transmission fluid.

If a pump fails on some hybrids, the system will disable the hybrid drive system or put the vehicle into a limp mode. Most hybrids also have an insulated coolant reservoir or jug that may have a pump of its own to help warm up the engine faster or keep the batteries at a constant temperature.

Not every car has an auxiliary water pump, but those that do can throw a monkey wrench in your normal diagnostic logic when solving cooling system problems.

You May Also Like

VIDEO: Engine Efficiency Brings More Hoses

Andrew Markel discusses hoses and the necessity for several of them to route fluids to all parts of the vehicle due to the growing efficiency of engines. Sponsored by Dayco.

oil-coolant-hoses-video-featured

Andrew Markel discusses hoses and the necessity for several of them to route fluids to all parts of the vehicle due to the growing efficiency of engines. Sponsored by Dayco.

Diagnosing Intelligent Cooling Systems

The majority of cooling systems on the roads react to what is happening inside the combustion chamber. After the engine is stressed, the heat causes the thermostat to open. Increases in temperatures will also cause the cooling fans to come on. The heat carried by the coolant is the trigger for operation of the fans and thermostat.

Modern Cooling System Design: It’s Not About Temperature; It’s About Powertrain

Given the advanced state of internal combustion engine technology, some recent cooling system innovations will actually increase engine torque and fuel economy while reducing exhaust emissions. Let me simplify that idea: new cooling system technology will make engines run better and cleaner. So, let’s get on the same page by reviewing some basics.

Modern Cooling System Design: It’s Not About Temperature; It’s About Powertrain

Reading engineering papers tends to be a boring exercise, but they do give a technician like myself a new perspective on how a common automotive cooling system could actually be improved. Of course, our immediate thought is how the cooling system can keep the engine cooler. Not so, according to one paper.

HFO-1234yf: Regulations And Requirements

SAE standard J2843, for “R-1234yf (HFO-1234yf) recovery equipment for refrigerants used in mobile air conditioning systems,” establishes the minimum equipment requirements for the recovery, recycling and recharging of R-1234yf.

Other Posts

Why Does Engine Coolant Need Replacement?

Two specifications can be used to justify replacement — the condition of the additive package & the freezing point.

Improving Turbocharger Longevity

It is estimated that by 2022, 50% or more of vehicles sold in the U.S. will have one or more turbochargers under the hood.

Mini Cooper Water Pump Service

The water pump is turned by a metal wheel driven by the crankshaft pulley.

Warn Your Customers About Water Pump Failure During the Summer

Summer is an opportune time for automotive professionals to remind customers to keep an eye on the signs of a failing water pump.  As you know, extreme summer temperatures and added strain on vehicles from activities like long road trips can cause engines to become more susceptible to troubles from excessive heat, making the function