Water Pump Problems

10 Paths to Water Pump Problems

Know your leaks

Leaks are the most common sign of water pump failure, but what type of seepage are you seeing and what does it mean?

A coolant leak coming from the weep hole is a sign of water pump bearing or seal failure. This weep hole often resides between seals that separate the oil side from the coolant side. A small amount of “dry” seepage around the hole can be considered normal, but it’s only a matter of time before a seal becomes defective and the seep turns into a drip.

A coolant leak into the front cover area, connected to the oil sump, means the outer O-ring has failed. This could mimic a head gasket leak.

Chevrolet water pumpCracking from coolant

Adding cold coolant to an overheated engine can cause thermal shock and create a seal leak even in a new water pump. Starting an engine during a water pump replacement before adding coolant could have the same effect. Look for a crack across either the seal face or the mating ring as evidence.

Allow an overheated engine to sit and cool before adding coolant. Then, restart the engine and allow it to run while slowly adding the remainder.

The damaging power of rust

Abrasive particles accelerate water pump seal wear. For example, systems that are not properly pressurized allow air to enter and foster the build up of rust. Or, if water with a high mineral content is added to the system and is heated, it will begin to form deposits that will accumulate and cause passage restrictions. Both of these are harmful to seals.

Although rust is difficult to remove, it should be flushed from the system as thoroughly as possible before the old water pump is removed.

Pay attention to the O-rings

When replacing the pump, O-rings need to be lubricated with either oil or coolant. Do not use silicone or other sealants that can block the weep hole.

water pump belt problemsBubble trouble

Cavitation is the formation of vapor cavities in a liquid as a result of forces acting upon the liquid, like rapid changes of pressure. Cavities form when pressure is relatively low, and then when subjected to higher pressure, the voids implode and can generate an intense shockwave. What’s this mean for a water pump?

Water pump efficiency can depend greatly on the impeller and housing design. If there is excessive turbulence as a water pump impeller circulates through coolant, cavitation can occur, which hurts pumping efficiency and can cause further erosion of the impeller and impeller housing.

Tying it in with the timing belt

Water pumps serve as an idler pulley on many engines equipped with timing belts and, due to accessibility issues on many transverse engines and the labor operations involved in replacing the timing belt (especially on imports), it’s cost-effective to invest in a new water pump as well, especially if the pump is near the 100,000- to 150,000-mile recommended replacement mark.

Watch for fan support

Water pumps can sometimes support a mechanical fan. If the fan assembly falters in some way, like from a bent fan blade or a severely cracked assembly, bearings can be affected. For evidence, look for casting breakage around the bearing support as this is typically caused by excessive vibration or an imbalance caused by a badly worn fan or clutch. To remedy, inspect the pulley, belt alignment and fan/fan clutch assembly, replacing any bent or worn components.

Blue discoloration?

Blue discoloration of the water pump shaft would indicate excessive heat buildup for some period, eventually ending in breakage of the shaft. This heat buildup can be caused by the tremendous centrifugal forces created by imbalance, which overloads the bearing and generates a ton of heat. A clean break indicates an “instantaneous” fracture caused by sudden overload or imbalance at the bearing.

To remedy, check the pulleys for proper alignment, straightness and fatigue. Inspect fan/fan clutch assembly for a bent or damaged fan, a worn spacer, or a worn or damaged fan clutch.

water pump diagnosticsWhy shaft bearings fail

Noisy shaft bearings are the second-most common reason for water pump failure. Most shaft bearings fail due to normal wear in the bearing or due to the normal oxidation of lubricant on the bearing surfaces. In rare cases, bearing failure can be hastened by over-tightening conventional accessory drive belts.

Impeller slippage in shaft

The less common water pump failure is the impeller slipping on the water pump shaft. A good water pump impeller will cause the pressure to increase as the engine is accelerated. If pressure does not increase, the impeller is slipping on the shaft or is missing impeller blades. In general, a good water pump should develop at least 10 psi of pressure above 2,000 rpm.

Since the impeller and shaft are a press-fit assembly, slippage occurs most frequently on remanufactured water pumps. In any case, ­slippage can be intermittent in nature and can depend greatly upon the temperature and speed of the engine.

Some replacement impellers can be manufactured from inferior metals that are susceptible to rust corrosion. In most of these cases, impeller blades begin to break away from the impeller due to a rust-through condition, which results in decreasing pumping capacity and an increasing presence of rust contamination in the cooling system.

You May Also Like

Toyota FJ Cruiser Water Pump Replacement

Toyota’s original Land Cruiser was the company’s version of a Jeep that could go anywhere. In its time it was highly rated and collected, which led the Japanese juggernaut to bring back an updated SUV in 2007 called the FJ Cruiser. The retro-styled vehicle was again a go anywhere machine powered by a 4.0L V6 (1GR-FE) used in the Tacoma. The engines are durable and considered relatively robust for the time.

Toyota’s original Land Cruiser was the company’s version of a Jeep that could go anywhere. In its time it was highly rated and collected, which led the Japanese juggernaut to bring back an updated SUV in 2007 called the FJ Cruiser. The retro-styled vehicle was again a go anywhere machine powered by a 4.0L V6 (1GR-FE) used in the Tacoma. The engines are durable and considered relatively robust for the time.

Long-Life Coolants Explained

Different types of coolants cover a range of applications from diesel to domestic, Asian and European vehicles. Each one is formulated to a specific manufacturer’s specifications to keep their engines at an optimal temperature. But, changes to the old one-size-fits-all formula has led to confusion for consumers and even some technicians.

VIDEO: Engine Efficiency Brings More Hoses

Andrew Markel discusses hoses and the necessity for several of them to route fluids to all parts of the vehicle due to the growing efficiency of engines. Sponsored by Dayco.

oil-coolant-hoses-video-featured
Diagnosing Intelligent Cooling Systems

The majority of cooling systems on the roads react to what is happening inside the combustion chamber. After the engine is stressed, the heat causes the thermostat to open. Increases in temperatures will also cause the cooling fans to come on. The heat carried by the coolant is the trigger for operation of the fans and thermostat.

Modern Cooling System Design: It’s Not About Temperature; It’s About Powertrain

Given the advanced state of internal combustion engine technology, some recent cooling system innovations will actually increase engine torque and fuel economy while reducing exhaust emissions. Let me simplify that idea: new cooling system technology will make engines run better and cleaner. So, let’s get on the same page by reviewing some basics.

Other Posts

Hybrid Vehicle Fluid Maintenance

There are opportunities your shop can’t pass up just because the car or SUV has a hybrid badge on the back.

Auxiliary Cooling Pumps

An auxiliary cooling pump’s primary function is to circulate warm coolant to the heater core.

Understanding Coolants

All-season coolant used inorganic acid technology and worked great for almost 30 years.

Monitor Water Quality When Servicing Coolant

The harder the water, the more likely the water pump is to develop a leak.